查询词典 extra error

However, as Zhang sected tangentical multiped station distance Zhang of cards and membership cards making-position when compared to paper for a relatively long, Zhang cut registration error to chromatometry methals overprinter error.

但由于弛切工位间隔弛切线的制卡和会员卡制息工位较近，纸弛比辛不幼，所以弛切的套准误不不差给比色间的套印误不不差相不不差不小一些。

Hypothesis in 0 ~ 10 speed range between 2000 and r/min speed error Δ requirement f r/min, more than 1 and measuring time, time than 100 ms t take 3 muon s acuities error Δ than eight mu t s, according to the formula (1) and (3) and assumptions, and computer programming.

假设转速范围在0～10 000 r/ min 之间，要求转速误差Δf ≤1 r/ min ，并且测量时间T ≤100 ms ，时间误差取3μs ≤ΔT ≤8μs ，根据公式(1)和(3)及假设条件，进行计算机编程求解。

The error model of normal direction is a simplified model of the previous one and is widely used in describing error of straight lines.

通过实例说明了εm模型是理论上更加严密的缓和曲线误差模型，而εm模型是一种简化的描述模型。

This dissertation points out the error caused by improper normal vector of surface in the shading operation of volume rendering, and a method to avoid the error is presented.

本文也指出了在整体显示的浓淡处理中，由于原有模型中曲面法向的不确定性所引起的错误，提出了一种新的计算法向的方法来避免曲面法向不确定的现象。

While the final error notification message appears on standard error stream.

而最后的错误通知信息出现在标准错误流中。

A simple of improving the differential frequency by D flip-flop is introduced. The method is verified by timing analysis. Numberical application conditions are given out. The reason for the error production is analyzed and the maximum error range are calculated.

介绍了D触发器差频的方法和应用条件，用最基础的时序分析的方法，对D触发器差频做一个理论上的验证，定量给出应用条件，并分析了产生误差的原因和最大的误差范围。

Sends and logs a complete error reply to the client. The numeric code specifies the HTTP error code, with message as optional, more specific text.

为客户端发送一个完整的错误回应并记录它。code 指定了 HTTP 错误代码，可选的 message 提供了更详细的信息。

But in the numerical calculation process, such as numerical differentiation, if we use these numerical methods inadequately, then it may be induced non necessary numerical error, including round off and truncation error.

因而常必须以值方法替代解析解，但是在值计算的过程中，很容引入额外的计算误差，包括舍位误差与截断误差。

Non-linear error is an important source of the machining error in multi-axis numerical controlled machining and it is unavoidable.

非线性误差是多轴数控加工中加工误差的重要来源，在多轴加工中不可避免。

The minor error of baseline length and obliquity will cause high terrain larger error.

基线长度和倾角的微小误差都会引起地形高度较大的误差。

Tom: You are right, he worked hard all the time.

你是对的。他一直都是努力工作。

Take shortcomings,failures,and mockings of others as commonplace and a drive to complete oneself,hold your own opinion over the evalution and disscution divested from others,afterwards sink into the state of eliminate mistakes if any or encourge oneself being not being influenced by the sayinngs of others or having no ideas to do.

把缺点、失败及别人的耻笑等看成是一种常事，当成完善自己的动力，对别人的评价和议论自己心中有主见，做到&有则改之，无则加勉&，不为人言所左右或无所适从。