查询词典 error condition

Experiments shows that it can detect the carrier frequency and the low frequency of modulation signal as expected, the resolution of the carrier frequency is 0.3Hz,the detecting error is within ±0.5Hz, and the resolution of the low modulation frequency is 0.07Hz, the detecting error is within ±0.05Hz.

实验结果表明该检测仪能很好地检测出信号的载频和信号的低频调制信息，其中信号载频的分辨率为0.3Hz，误差范围在±0.5Hz 以内，低频信息的分辨率可达0.07Hz，信号的误差在±0.05Hz。

This paper presents a new effective error-control coding-the double catercorner line redundancy code, which overcomes some defects of the several error controlling codes.

针对常用的差错控制编码存在的缺陷，提出了一种新型的差错控制编码－双向斜行列校验码。

In this paper, according to the characteristics of central projection, aerial photographs were analyzed to discuss displacement of images under tilt conditin or caused by ground undulation, based on which the principles of tilt error and projection error were summarized.

根据中心投影的特性，论述了像片在倾斜条件下所引起的像点位移和像片因地面起伏而引起的像点位移，在对其进行分析的基础上总结出倾斜误差和投影误差的规律，从而说明了不能把像片当作地形图使用。

In this paper, according to the characteristics of central projection, aerial photograph s were analyzed to discuss displacement of images under tilt conditin or caused by ground undulation, based on which the principles of tilt error and projection error were summarized.

本文以航空摄影测量像片为分析对象。根据中心投影的特性，论述了像片在倾斜条件下所引起的像点位移和像片因地面起伏而引起的像点位移，在对其进行分析的基础上总结出倾斜误差和投影误差的规律，从而说明了不能把像片当作地形图使用。这是使用航空像片时必须注意的基本问

Results The measurement error of dental cast analysis is less than 0.09 mm,and the error of three-dimentional cephalometry is less than 0.45 mm.

结果 经检测，模型立体分析的误差小于0.09mm，三维头影测量系统精度为0.45 mm，符合临床要求。

Contour Error of linear and circular motion is caused by following error of each axis position servo system.

由于位置伺服系统跟随误差的存在，导致直线和圆弧运动时产生轮廓运动误差。

It showed the correctness of the criteria of roundness error and relationship between the minimum zone circle, minimum circumscribed circle and maximum inscribed circle and the effectiveness of the methods for evaluation of roundness error.

也验证了圆度误差判别准则及最小区域圆、最小外接圆和最大内接圆特征点间的相互关系的准确性和误差评定方法的有效性。

Thus, evaluation of the minimum zone circle could be solved effectively.Three methods of assessment of roundness error were proposed in this dissertation. Based on the criteria of the minimum zone circle, minimum circumscribed circle and maximum inscribed circle and convex hull, a unified approach was proposed to evaluate roundness error of the minimum zone circle, minimum circumscribed circle and maximum inscribed circle. Evaluation of the minimum zone circle, minimum circumscribed circle and maximum inscribed circle was fulfilled with rotation based the contact pattern. The minimum circumscribed circle and maximum inscribed circle were evaluated with curvature and the curvature circle.

本文提出了三种圆度误差评定的方法：根据最小区域圆、最小外接圆、最大内接圆在极坐标系下的判别准则，利用计算几何中的凸壳理论，提出了一种统一的评定方法，实现了对最小区域圆、最小外接圆、最大内接圆的误差评定；基于接触斑点的检验原理，利用旋转法，实现了最小区域圆、最小外接圆和最大内接圆的误差评定；利用曲率和曲率圆，实现了对最小外接圆和最大内接圆的误差评定。

By means of analyzing the influence of OD surface roundness error on the outer raceway of bearing ring, the processing method of bearing on internal grinder electromagnetic centerless clamper was improved, the influence of roundness error on outer raceway was decreased, meanwhile, the product quality was raised with less waste products.

通过分析轴承环外径表面圆度误差对轴承环外滚道的影响，改进了轴承在内圆磨床电磁无心夹具上的加工方法，降低了轴承环外径定位表面圆度误差对轴承环外滚道的影响，提高产品质量，达到了降低废品损失的目地。

As the research of the error-correction coding theory going deep, the error-correction code has been widely applied.

随着纠错编码理论研究的不断深入，纠错码的实际应用也越来越广泛。

For the head-teacher of the class said that I had seriously broken the school rules,which led me to a three-day suspend class.

为什么呢？因为我的班主任说我严重的违反了校规，于是让我停课三天。

Many of them believe that the conversion of thousands of working-class folk in England spared that nation from the mass carnage and the tyranny that came with the revolution in France.

他们之中有许多人相信，在英国数以千计的劳工阶级之悔改信主使英国免於遭受如法国大革命所造成的大屠杀和专制暴政。