查询词典 equalizing gear

A kind of new typed epicyclic gear transmission with few teeth difference d inner plane motion of spur gear and possessing practical value was put forward in this study.

提出了一种具有实用价值的外齿轮内平动式的新型少齿差行星传动。

The selflock conditions and the selecting range of transmission ratio of power in closed epicyclic gear trains can be used in common differential gear trains, too.

本文基于啮合功率法推导出封闭周转轮系效率计算的统一公式，大大简化了封闭周转轮系效率计算难度。

Several methods, which can be used to determine the type of power stream in the gear trains and the selflock condition of closed epicyclic gear trains, are figured out.

有关封闭周转轮系的自锁条件和传动比选择范围同样适用于一般差动轮系。

For spiral bevel gears' formate gear, using proper figurate cutting tool and generic CNC machining center, the gear's hard tooth-surface can be milled with high speed.

螺旋锥齿轮副的成形法大轮，利用合适的成形铣刀，在通用的立式加工中心上，可以实现热处理后硬齿面的高速铣削。

Whether it or not to improve the lubrication and dynamic performance of gear, at the same time to realize a "green lubrication" type of gear transmission of low cost, energy saving and easy maintenance by means of making use of the frication material"s lubrication performance and meshed medium"s elastic deformation?

能不能研究一种利用摩擦副材料的摩擦润滑特性和啮合介质的弹性变形，实现既能改善齿轮的润滑和动态特性的效果，又能实现低成本、节能、易维护的绿色润滑齿轮传动？

It is proved that the method using the BEM to calculate the load distributions on the contact lines of involute gear pair, in which the applied load is taken in the form of a concentrated one at a single node, is not suitable. A method in which the tractions of the BEM are made to imitate the Hertzian pressure of the gear using 8 nodes isoparametric elements is introduced.

本文解决了边界元法在空间啮合副计算中存在的系数矩阵的存储，奇异单元积分的计算、表面不连续点处面力一点多值和求解未知量的线性方程组矩阵元素的计算等问题，编制了比不采用上述处理方法的一般边界单元法节省近一半内存和计算时间的适合空间啮合副的三维边界元法计算程序。

Because of the especial requirement of gear form of preshaving hob The design of preshaving hob is more comples than common gear hob.The design method is inefficience,takes much time,and requires highly of designers.

拉刀也是机械加工中常用的一种刀具，拉削可加工内表面（如各种型孔、键槽、花键孔等）和外表面（如平面、半圆弧面和组合表面等）拉削加工效率高，精度高。

The closed picture of involuted gear can not be applied to that of the point-line meshing gear.

封闭图主要确定大齿轮变位系数x2与螺旋角β，这样就相应地确定了其他参数。

The selections of parameters between point-line meshing gear and involuted gear are different while designed.

点线啮合齿轮的封闭图与齿数z1、z2及刀具参数有关，而与中心距a及模数mn无关。

Main lambdoidal transmission gear of the great girder rolling mill is the key machine of this system.. It"s belongs to big modulus wide gear enduring heavy loads so it"s surface is easy to be hurt.

大型轨梁轧机主传动人字齿轮是轧机主传动系统的关键设备，该人字齿轮是大模数宽齿轮，承受载荷较大，易对齿面造成损伤。

Mr. Putin said there were signs of genocide against the Ossetian people.

普京说，有迹象表明对南奥塞梯人进行了种族清洗。

What I'm trying to say, Tristan is...

特瑞斯坦。我想说的是。