查询词典 electrodes

The electrodes are available for both AC and DC arc welder.

采用该种焊接材料作为填充金属用于Cr-M。

One-way analysis of variance was used to test for an association among complete esr thresholds and linear correlation was used to examine the association between esrt and m-levels of all four test electrodes.

对四个测试电极之间的esrt进行方差分析，并对测试电极的esrt与 m级进行相关性分析。

Heat is supplied from electricity that arcs from the electrodes to the metal bath.

装料大部分为小片的生产不锈钢的电炉。热量由从电极到金属液的电流提供。

Butt Weld and docking and corner combinations Weld, in Weld ends located arc plate and extraction plate in igniting board then leads to the welding seam, joint halfway shall weld joints in front of 2.0 mm Department Firing arc, welding pieces after preheating rod will return to weld the origin, pool filled to the required thickness, before forward welding; Welding speed : Isokinetic welding requirements to ensure weld thickness, width uniform, which masks to look for hot metal and slag bath equidistance (2-3 mm)%; Arc welding rod length : different models and determined that the general requirements of arc length is stable, acid electrode generally 3-4 mm, 2-3 mm normally alkaline electrode%; Welding perspective : According to determine the thickness of two pieces of welding, welding angle has two aspects : First, the angle between the direction of the rod and welding of 60-75 ; The second is the angle between two electrodes and welding around, the same thickness as welding, welding and welding pieces incident angle of 45 ; When the thickness ranging from welding, welding electrode and thick and thin pieces of welding electrode side angle greater than the angle between the side pieces; Arc : admission to the end of each weld should be filled crater, in the direction opposite to the direction of the back-arc welding, arc welding unchanged inside pit in 1974, to prevent the crater bite of meat.

对接焊缝及对接和角接组合焊缝，在焊缝两端设引弧板和引出板，必须在引弧板上引出后再焊到焊缝区，中途接头则应在焊缝接头前方15～20㎜处打火引弧，将焊件预热后再将焊条退回到焊缝起始处，把熔池填满到要求的厚度后，方可向前施焊；焊接速度：要求等速焊接，保证焊缝厚度、宽度均匀一致，从面罩内看熔池中铁水与熔渣保持等距离（2～3㎜）为宜；焊接电弧长度：根据焊条型号不同而确定，一般要求电弧长度稳定不变，酸性焊条一般为3～4㎜，碱性焊条一般为2～3㎜为宜；焊接角度：根据两焊件的厚度确定，焊接角度有两个方面，一是焊条与焊接前进方向的夹角为60～75 ；二是焊条与焊接左右夹角有两种情况，当焊件厚度相等时，焊件与焊件夹角为45 ；当焊件厚度不等时，焊条与较厚焊件一侧夹角应大于焊条与薄焊件一侧夹角；收弧：每条焊缝焊到末尾，应将弧坑填满后，往焊接方向相反的方向带弧，使弧坑甩在焊道貌岸然里边，以防弧坑咬肉。

Packed bed electrodes can reach higher current densities at relatively low electrode polarizations,which is favorable to mitigating the inconsistency between reaction rate and selectivity.

填充床电极具有大的内表面，能在相对低的极化下，达到较高的表观电流密度，有利于缓解反应速率和选择性之间的突出矛盾。

Carbon nanotubes—hollow, tube-shaped lattices of carbonatoms—can be used to make a mechanical memory that works by bending thecarbon filament up or down to make or break a connection between two electrodes.

碳纳米管能用于制造机械的存储器，它通过上下弯曲碳丝从而接通或断开两个电极之间的连接而工作。

Carbon nanotubes—hollow, tube-shaped lattices of carbon atoms—can be used to make a mechanical memory that works by bending the carbon filament up or down to make or break a connection between two electrodes.

碳纳米管能用于制造机械的存储器，它通过上下弯曲碳丝从而接通或断开两个电极之间的连接而工作。

The electrochemical behavior was studied at different electrodes by cyclic voltammetry, which showed significant electrocatalytic effect of the silver electrode on the reduction of benzyl chloride.

通过循环伏安法研究了苄基氯在不同电极上的电化学行为，结果表明了银电极对苄基氯的还原具有很强的电催化效果。

After that,an isotropic undercutting process for forming the upper control electrodes and contact bar under the bridge was proposed to obtain plane bridge film.

通过改进工艺，提出了一种侧向钻蚀刻蚀介质桥膜下金属的方法，获得了平坦的介质桥膜。

When fitted with carbon electrodes, this lamp was used as a light source for projectors .

当装有碳电极，这盏灯是用来作为光源的投影。

World War II: Battle of Saipan - Americans take Saipan.

1944年的今天，美国在塞班战役中拿下塞班岛。

When the scorner, the rejecter of truth, has become presumptuous; when the routine of work in the various money-making lines is carried on without regard to principle; when the student is eagerly seeking knowledge of everything but his Bible, Christ comes as a thief.{DA 635.3

当讥诮和拒绝真理的人，到了任意妄为时，当追求财利者罔顾按道义经营谋利时，当学人正在兢兢业业地研究各种知识，而单把圣经丢在一边时，基督要像贼一样来临。