查询词典 die block

The fields include Food Molding Die; Zipper Die; Cigarette Bronzing Mould(including roller Bronzing mould); Skin-vein and pattern stamping Mould; profile-cutting-edge Die; Badge Mould; PCB Mould used in car; Stereo Tremble Film molding Die; Tile Vein Mould; Plastic Raster Molding Mould(used in 3D- picture card and shoes); Secret Engraving Die.

公司技术总监在餐具成型模、拉链模、香烟烫金模、模切刀口模、徽章模具、汽车用电路板模具、皮纹压花模、手机环绕立体声震动膜成型模具，瓷砖模，应用于动画卡和凉鞋上光学干涉模等，有着极为丰富的设计制造经验，其中有些制造工艺是独创的，连欧美日企业也没有掌握。

I plant main products: Carbide special-shaped mold, drawing die, cold heading Die, Die a straight shrink die, die of natural diamond, the first core, the letter rod, roll, drawing equipment and all kinds of resistance Carbide Grinding parts.

我厂主要产品有：硬质合金异型模具、拉拔模具、冷镦模具、冷冲模具、直缩模具、天然金刚石模具、芯头、信棒、轧辊、冷拔设备及各种硬质合金耐磨零件。

Select the die-cutting machine bearing in mind that is suitable for printing production, die-cutting with a thick sheets can choose to use flat-bed die, die-cutting thin paper you can choose to use rotary die-cutting machine.

选择模切机要注意适合印品的加工要求，模切较厚的纸张时可以选用平台式模切机，模切较薄的纸张则可以选用轮转模切机。

So we can turn die pricing of die state-owned share to die pricing of die stock on die condition of full-flowing.

于是模型将国有股合理价格的求解问题转换成全流通条件下股票价值的求解问题。

The die of NC tube bending is composed of bending die,clamp die,wiper die,pressure die and mandril.

导管数控弯曲模具包括弯曲模、夹模、压模、防皱模和芯棒。

An improvement on the die casting technology of aluminium hub includes drilling hole at the position of die, where the function of die is not affected, for preventing gas from coming into molten aluminium, mounting safety valve to the exhaust opening of die casting case for keeping proper pressure to save electricity and shorten die casting time, and increasing the water-flowing area of cooling disk or ring for higher cooling effect.

一在不影响模具本身功能部位钻孔增加排气通道，解决了压铸过程中产生的气体进入铝水问题。可使铝轮减少气孔。在压铸机箱体排气口部位，安装安全阀，能使压铸机箱体内保持适当的压力，工作时少进气、少排气，起到节电不堵浇口，缩短压铸时间，提高产量。冷却盘、冷却环改进后，增加了过水面积，提高了冷却效果。

The structures of solid a phase of original billet, pierce block in the chamber of die-casting machine, ingate block in die-casting mould and specimens atdifferent locations in a semi-solid die casting component were observed.

实验观察了原始料坯，压铸机压室内的冲头料坯以及压铸模内的内浇口和半固态压铸零件中不同部位的固相α组织的形貌。

Integrating trellis-coded modulation with threaded algebraic space–time block code, trellis-coded modulation space-time block code is presented, which has the advantage of full-diversity and small detection delay. Based on TCM pre-processing, the minimum distance between different codeword matrixes of the TCMST block code is maximized, so the average bit error rate of the TCMST block code is lower than that of the TAST block code at the same signal noise ratio.

TCMST分组码具有满发送分集度和检测延迟小等优点；由于采用了TCM预处理，使得不同TCMST分组码码字矩阵间的最小距离达到了最大化，因此在相同信噪比情况下，TCMST分组码具有比TAST分组码更低的平均误比特率。

Traveling Block - The block and tackle which is rigged with the crown block by multiples of drilling line strung between the crown block and the traveling block.

游动滑车：通过排列穿过天车和游动滑车的多股钻井绳和天车装配在一起的滑轮及装备。

From the perspective of geologic evolution, this paper discusses the conformation features of fault block, emphatically demonstrates the closure property of the margin of complex fault block and the controlling of the fault block internal structure on accumulation of CBM, and points out that the synclinal and synclinorial areas of thrust fault block and structurally triangle fault block areas would be favorable for CBM occurrence.

本文从构造演化出发，讨论了区内复杂断块的形态类型特征，着重论述了复杂断块体边界断裂的封闭性以及断块体内部构造配置对煤层气成藏的控制作用。分析得出逆冲断块的向斜、复向斜区域和构造三角断块区是煤层气成藏的有利区块。

Chinese traditional virtue is humility and wariness,the compliment and praise to the others should be declination

中国人的传统美德是谦虚谨慎，对别人的恭维和夸奖应是推辞。如

We bought this house on the never-never.

我们以分期付款的方式买下这座房子。