查询词典 calculation error

Through field measurement for the contact pressure of box foundation with Ⅰ shaped plane of a high rise building on cobble subsoil, the distribution law of the contact pressure has been diagrammed. At the same time, the contact pressure has been calculated with finite compression layer model, which is well accordant with the measured result. The relative error of average value for the measured to the calculated contact pressure is 6.9%. This shows that the numerical calculation is right.

通过对西南交通大学某教学楼箱形基础基底反力的实测结果，得出了&Ⅰ&形平面箱基置于密实卵石层上的基底反力分布规律，又用有限压缩层地基模型对该箱基反力进行了计算，结果表明：实测反力与计算反力分布规律一致，实测反力平均值与计算反力平均值相对误差为6.9％，也说明此法计算箱基反力是可行的。

It is introduced that with two total station instrument s after transforming to set up the station arbitrarily,the deduction for formula and the calculation for error are made to evaluate the differences in elevation with the subtending measurement of trigonometric leveling.

介绍了用两台改造后的全站仪任意置站的方法进行三角高程对向测量求取高差的公式推导和误差计算，论述了用三角高程测量代替二、三等水准测量的可行方法，测量时不必量取仪器高、目标高，减少了三角高程的误差来源，加快了施测速度。

It is introduced that with two total station instruments after transforming to set up the station arbitrarily,the deduction for formula and the calculation for error are made to evaluate the differences in elevation with the subtending measurement of trigonometric leveling .

介绍了用两台改造后的全站仪任意置站的方法进行三角高程对向测量求取高差的公式推导和误差计算，论述了用三角高程测量代替二、三等水准测量的可行方法，测量时不必量取仪器高、目标高，减少了三角高程的误差来源，加快了施测速度。

Based on the 3D time-average Navier-Stokes equations, k-ε model was used to simulate the 3D turbulent flow field of whole flow passage in the Francis turbine including guide wickets, runner and draft tube. The energy performance and cavitation performance were predicted from the simulation results, and the calculated data were compared with the results of hydraulic turbine model experiment. The calculation of turbine efficiency and the measured efficiency was very closed and the maximal relative error was 0.9%.

该文基于Navier-Stokes方程和k-ε紊流模型，采用贴体坐标和交错网格系统，用SIMPLEC算法对一模型混流式水轮机引水元件、转轮和尾水管进行了联合计算与转轮单流道计算，数值模拟了水轮机各通流元件内部三维湍流流场，预测了水轮机的能量性能和空化性能，并与水轮机模型试验结果进行了对比。

On the project background of Rongzhou Bridge, a half through CFST arch bridge in Yibin crossing Jinshajiang, the optimizing theory is applied to the calculation of the stayed-buckle-cable forces in the process of craning construction of the steel-tube arch segment and construction error adjusting. The calculated optimum cable forces with high precision can guarantee the inner forces and the structuredeformation in safe state, and ensure the line shape of the arch ring in accordance with design requirements as well.

以宜宾金沙江戎州大桥(主跨260m的中承式钢管混凝土拱桥)为工程背景，将优化理论引入到钢管混凝土拱桥拱肋架设和扣索索力调整计算，这样计算出的索力精度较高，既能确保结构的受力状态和变形始终处在安全范围内，又能保证架设和调整后的拱肋线形符合设计期望。

Aimed at the specialty that avion weapons move fast and targets move slowly , this thesis analyses the collision error and brings forward an algorithm to solve the collision calculation problem when missiles are used to attack targets.

针对军机武器运动快，而靶标运动相对较慢的特点，分析了其碰撞的误差问题，提出并建立了一种解决导弹攻击目标时的碰撞解算方法。

The design paramters can be used to measure various very well,and the calculation error and design complexing are reduced.

利用该设计能够很好地测量各项电力参量，极大地减小了计算上的误差和设计复杂性。

The calculation of the rolling time shall not account for the times required for reduced rolling speed due to material faults, operator's error, pause, repair, maintenance, test program change and the other downtimes, for which Seller is not responsible.

轧制时间的计算不包括由于材料的问题，操作人员的失误，暂停，维修，保养，测试程序的改变等浪费的时间和其他时间，卖方对此不负责。

Characteristic and calculation of fire error for the main tank using HEAT are discussed.

介绍了坦克使用某型破甲弹射击时射击误差之特点和计算问题。

However, as a result of the calculation and regulation error of cutting machine, the spiral bevel gears that are produced by cutting once are difficult in attaining good contact and transmission quality. Therefore, it is necessary to simulate the transmission of real gears and then to find optimal cutter and cutting machine parameters.

但是，由于人为计算和生产、调整过程的误差，一次试切加工出的弧齿锥齿轮一般难以达到最佳的接触传动质量，因此根据现有切削参数对弧齿锥齿轮进行接触传动的仿真，从而找出较好的切齿刀盘和机床调整参数是非常必要的。

"Second Life is remarkably easy to work with, and is very popular,"

"第二次生命是显着容易的工作，并且很受欢迎，"

For example, we usually assume that materials are homogeneous and isotropic and free of internal defects or flaws.

为了得到适合有限元分析的模型，我们必须经过如图2所示的简化步骤。