查询词典 arithmetic device

But in practical operating, overvoltage caused by reignition of the vacuum switching device frequently appears, and it result in damage of the capacitor bank or the switchgear itself. Ensuring the switchgear against reignition and installing a protective device are two main approaches to avoid the phenomenon. In this paper, a study on overvoltage caused by reignition due to capacitor bank switching with the vacuum switching device and its preventive measures are carried out. The main work which has been done and researches are as follows: 1. The producing mechanism of overvoltage and its influence factor are analyzed. It is pointed out that single-phase reignition is the main reason for damage of the switchgear and two-phase reignition is the main reason for damage of the capacitor bank,so overvoltage of single-phase reignition and two-phase reignition are the emphases of prevention. 2. Analysis of the special working condition of the operating switch for capacitor bank is carried out. It indicates that the vacuum switching device is difficult to realize no-reignition under this operation condition, so it is more practical to adopt protection devices. 3. Analyses of protection effect of RC and MOA and their shortages are carried out. It shows that the two methods can only restrain effectively overvoltage caused by single-phase reignition, and they cannot protect the capacitor bank when reignition of two-phase occurs. 4. The operation principle of G-R damping device is analyzed and discussed emphatically.

本文针对真空开关投切电容器组时因重燃而产生的过电压及其防治措施进行了研究，所开展的主要工作和研究结果如下： 1、对过电压的产生机理及其影响因素进行了分析，指出单相重燃是导致开关设备损坏的主要原因，而两相重燃则是导致电容器组损坏的主要原因，因此单相重燃和两相重燃过电压是防护的重点； 2、对电容器组操作开关的特殊运行条件进行了分析，指出在这种运行条件真空开关难于实现不重燃，因此采用保护装置更具有现实意义； 3、对RC与MOA的保护效果和存在的不足进行了分析，指出这两种方法均只能有效抑制单相重燃过电压，而不能在发生两相重燃时保护电容器组； 4、重点对G-R阻尼装置的工作原理进行了分析和讨论，指出该装置接入后线路中将会出现两种频率的高频振荡，而电容器组上的过电压是由这两种振荡共同决定的； 5、根据对上述两种振荡的分析指出存在一个最佳电阻值使得过电压最低，并提出了电容器组电压和最佳电阻值的近似求解方法； 6、使用电气暂态分析软件MATLAB对G-R装置的保护效果进行了仿真计算，证实该装置确实可以有效抑制重燃时的电容器组过电压； 7、根据仿真与近似计算结果的偏差提出了近似计算的修正方法，经过修正后的过电压计算结果与仿真结果吻合较好； 8、对G-R装置中放电装置G与阻尼电阻R的要求进行了分析，指出采用编织电阻和真空间隙可能是最佳选择。

Safety Belt Tension Furling Device: While a collision happens, if the driver uses a safety belt without tension furling device, the injury may happens by the collision on the instrument board or the steering wheel etc.; Safety belt tension device uses the gas generator in the safety belt tension furling device touched by the speed acceleration of collision, the gas expansibility generated will make the tension device rotate in the reverse direction, bringing the passengers back on the seats, protecting the passenger's security.

对于安全带预张紧卷收器：在发生碰撞事故时，若使用非张紧普通安全带，仍然有可能触及汽车方向盘和仪表板等部位而使乘员受伤；预紧式安全带利用撞车时的加速度触发安全带卷收器中的气体发生器，产生的气体膨胀力使卷收器反向旋转而收紧织带，将乘客向后拉向座椅，从而更可靠地保护乘客的人身安全

A high-precision liquid filter includes a liquid treating device among which the interior has a filtrating device with filter screen along the periphery set up, the lower end of its one side is the liquid inlet, and the upper end is the treated liquid outlet and the lower end is the impurity outlet, a steel plate for hoisting the filtrating device is set up in connection below the cover shell at the upper end of liquid treating device in which or on its outside a magnetizing device is further set up and on its bottom two stands are fixed.

高精度液体过滤器，包括一液体处理装置，其中内部设置有周缘设置有滤网的过滤装置，其一侧下端为液体入口，上端为处理过的液体出口，下端为杂质出口，处理装置上端盖壳下连设一用以吊设过滤装置的钢板，液体处理装置内或外侧还设置有一磁化装置，液体处理装置底部设有两支架。

Taking a general view of the paper, major innovative ideas and returns are as follows: The main innovative ideas are as follows: 1. The paper put forward the new idea that combine water-saving drilling with rotary percussion drilling creatively according to the present situation of water resource lack seriously and the background of implementation of state geological survey strategy. 2. The working principle of new designed system of water-saving hydraulic percussion device completely different from traditional hydraulic percussion device, the system can carry out rotary percussion drilling on the condition that no surface water be consumed, and achieve the purposes that saving surface water, cutting cost and improving drilling efficiency. 3. The design conception of steel ball percussion device is very novel, the percussion device is durable, with a simple structure, at the same time drilling efficiency would be improved highly and drilling cost would be reduced greatly when drill with the steel ball percussion device.

综观全文，论文的主要创新点及研究成果如下：主要创新点： 1、结合我国许多地区水资源严重短缺的现状以及国家实施地质大调查战略的背景，创造性地提出了&节水钻探&和&回转冲击钻进&结合起来的新思维； 2、设计出的节水型液动冲击器系统，其工作原理跳出了传统液动冲击器要消耗大量地表水的原理模式，在基本不消耗地表水的情况下便能实现回转冲击钻进，达到节约地表水、降低成本、提高钻探效率的目的； 3、设计的球体冲击器构思新颖，克服了同类产品冲击功传递效率低的弊端、且结构简单、经久耐用，可大幅度提高钻探效率、降低钻探成本。

The brake device is preferably a caliper brake device such as a cantilever brake device, a side pull brake device, or a center pull brake device.

制动装置最好是一悬臂制动装置之类的卡钳式制动装置，侧拉式制动装置，或中心拉动式制动装置。

In this thesis, the basic arithmetic of PIV software - cross-correlation arithmetic is introduced in detail, During the data process, through processing the two sequential images by the cross-correlation arithmetic, the vector charts of particles velocity can be obtained, so is the chart of absolute velocity, with velocity decomposed into the radial velocity and axial velocity.

本文对试验所获得的连续图像通过互相关算法，获得颗粒速度矢量图，并将速度分解为径向速度和轴向速度，对每一小区域内的颗粒按速度方向不同进行速度平均，获得颗粒的平均速度分布曲线。

We have accomplished under mentioned arithmetic in the project, which are the wavelet zero tree coding arithmetic based on difference signal and the non compression arithmetic based on the integer wavelet transform of interested area. We have achieved the huge amount of data processing and storing in real time、high speed and multi-channel.

完成了基于差分信号的小波零树编码算法和基于感兴趣区域整数小波变换的无损压缩算法，实现了高速、多通道、在线实时信号的处理存储。

using the c language programming to be in progress when secretly scheming against often may produce problem because of not paying attention to a type change , when using the division arithmetic magic figure especially, change , lead to thereby arithmetic result block of wood rightness or insufficient problems of accuracy often because of not paying attention to the arithmetic data type.

使用c语言编程进行计算的时候常常会因为不注意类型转换产生问题，尤其是在使用除法运算符"/"的时候，经常因为没有注意运算数据类型转换，从而导致运算结果不正确或着说是精度不够的问题。

First the math theory of machining simulation is studied, and the set structure of NC machining simulation system whose components, including time, input, output and so on, are defined. Hereby we set up the hierarchy structure, the logical structure, the static model and the dynamic model of simulation system. The construction method of sweep entity of cutter and rotation parts is researched, and their differential geometry invariants are calculated. NC code is unscrambled, and the recursion division arithmetic of time segment is put forward, which is the driven data of the movement or rotation parts. The CLDATA should be interference-free. To examine if there is interference between cutter flank and the work piece, an arithmetic that discussed the existence of intersecting curve between them is put forward. To examine if there is interference between two turrets, an arithmetic that discussed the existence of intersection set between two polygons is put forward.

首先研究加工过程仿真的数学基础，然后定义数控加工仿真系统的集合结构及时间集、输入集、输出集等概念，建立加工仿真的层次结构和逻辑结构，阐述双刀车削仿真系统的静态模型和动态模型建立方法，分析刀具扫描体和旋转部件扫描体的建立方法及其微分几何性质；研究NC代码解读技术和双刀加工时间段递归子分划技术，为驱动各仿真单元作数据准备；通过讨论后刀面和工件表面交线的存在性判断刀具后刀面与工件间是否干涉，通过求多边形的交集判断刀架与刀架是否干涉。

The disquisition brings forward three principle in combination arithmetic designing and combination arithmetic choice. There is currency, countability and less information redundancy. And the disquisition analyses the relation of them. The three principle is the dominant ideology in combination arithmetic designing.

组合算法的选择与应用组合算法评价依据复杂性选择应用本文提出了在组合算法设计和组合算法选择方面所应当遵循的三个原则，即通用性、可计算性和较少的信息冗余量，并初步分析了它们之间的相互关系。

Tom: You are right, he worked hard all the time.

你是对的。他一直都是努力工作。

Take shortcomings,failures,and mockings of others as commonplace and a drive to complete oneself,hold your own opinion over the evalution and disscution divested from others,afterwards sink into the state of eliminate mistakes if any or encourge oneself being not being influenced by the sayinngs of others or having no ideas to do.

把缺点、失败及别人的耻笑等看成是一种常事，当成完善自己的动力，对别人的评价和议论自己心中有主见，做到&有则改之，无则加勉&，不为人言所左右或无所适从。