查询词典 arbitrary element

In this paper we analyse a 12-parameter rectangular plate element which can be constructed by means of Coons surface method and further full error estimates for the element are established.

在本文中，我们分析了由郑照北利用 Coons 曲面方法构造的一个 1 2参数矩形板元并给出了相应的误差估

If drop finds its element in the set, it decrements the element's reference count and the number of elements in the set.

如果drop函数在集合中发现了其参数所指向的元素，便将该元素的引用计数器和集合的计数器减一。

If drop finds its element in the set, it decrements the element's reference count and the number of elements in the set.

如果drop函数在集合中发现了其参数所指向的元素，便将该元素的引用计数和集合元素数减一。

If drop finds its element in the set, it decrements the element's reference count and the number of elements in the set.

如果drop函数在集合中发现了其参数所指向的元素，便将该元素的引用计数器和集合元素数减一。

Pop deletes the last element of array, decrements the array length, and returns the value of the element that it deleted.

方法pop将删除array的最后一个元素，把数组长度减1，并且返回它删除的元素的值。

As the key element of the thermostatic valve the temperature sensing element plays the role of temperature sensing and force outputting.By absorbing the heat of the working fluid,the temperature sensing medium produces the capacity expansion which moves the regulating sleeve to control the fluid flow of input to control the temperature.

感温元件作为温控阀的关键元件起着感知温度和输出力的作用，感温介质吸收工作流体的热量产生体积膨胀，推动调节套筒调节进口冷热流体流量从而控制出口温度。

In the last part, analysis of the sound field around the shell of the fan is done with combining finite element method and boundary element method by using software ANSYS and SYSNOISE.

第四部分分析风机外壳周围声场，结合有限元法和边界元法，应用ANSYS和SYSNOISE软件，建立声场边界元模型。

Calculation and analysis the effects of primary flow parameters and structure parameters such as fliter volocity of flow,diameter of ceramic particle,void fraction of ceramic,section shape of ceramic filter element on filter efficiency and pressure drop of regid candle ceramic filter element in this paper.

计算和分析了渗流流速以及陶瓷颗粒直径、孔隙率、陶瓷过滤元件截面形状等主要流动参数与结构参数对于刚性烛状陶瓷过滤器过滤效率和过滤流动的压力降等特性的影响。

In this dissertation the"Penalty"finite element method was employed to compute the velocity of the three-dimensional flow of power-law fluid in a profile die. In order to decrease the needed computer memory and raise the stability of numerical simulation, a set of decoupled methods such as PFEM, pseudo-body force method and transformation of momentum equation to the elliptic equation was developed to establish the general finite element equations to compute the distributions of velocity and viscoelastic stress of the three-dimensional viscoelastic flow of the Phan ThienTanner fluid in a profile die. During numerical simulation of the extrudate swell of the PTT fluid, the flow in the die and out of the die was analyzed separately, which demands less computer memory.

本文建立了求解挤出口模内幂律流体流动速度场的通用三维罚有限元模型；对于非线性粘弹性的Phan Thien-Tanner流体，为了降低模拟计算对计算机硬件的要求，并使模拟计算更加稳定，采用了一种去耦算法，包括罚有限元方法、拟体力方法和动量方程的椭圆类方程转化方法，并建立了求解速度场和粘弹性应力场的总体有限元方程；对于PTT流体的挤出胀大问题，提出了挤出胀大熔体口模内外分离模拟法，这样可以显著降低数值模拟对计算机硬件的要求。

In this dissertation the"Penalty"finite element method was employed to compute the velocity of the three-dimensional flow of power-law fluid in a profile die. In order to decrease the needed computer memory and raise the stability of numerical simulation, a set of decoupled methods such as PFEM, pseudo-body force method and transformation of momentum equation to the elliptic equation was developed to establish the general finite element equations to compute the distributions of velocity and viscoelastic stress of the three-dimensional viscoelastic flow of the Phan ThienTanner fluid in a profile die. During numerical simulation of the extrudate swell of the PTT fluid, the flow in the die and out of the die was analyzed separately, which demands less computer memory. The key techniques used in numerical simulation of the three-dimensional extrusion from dies such as decision of boundary conditions, creation of initial velocity field, selection of penalty factor, high Weissenberg number problem , regeneration of the free surface were studied in detail.

中文题名聚合物异型材口模挤出三维流动研究副题名外文题名 Study on three-dimensional flow of polymer melts during the process of profile extrusion from dies 论文作者涂志刚导师柳和生包忠诩教授学科专业材料加工工程研究领域\研究方向学位级别博士学位授予单位南昌大学学位授予日期2001 论文页码总数148页关键词挤出成型聚合物材料挤出口模聚合物异型材馆藏号BSLW /2003 /TQ320 /9 本文建立了求解挤出口模内幂律流体流动速度场的通用三维罚有限元模型；对于非线性粘弹性的Phan Thien-Tanner流体，为了降低模拟计算对计算机硬件的要求，并使模拟计算更加稳定，采用了一种去耦算法，包括罚有限元方法、拟体力方法和动量方程的椭圆类方程转化方法，并建立了求解速度场和粘弹性应力场的总体有限元方程；对于PTT流体的挤出胀大问题，提出了挤出胀大熔体口模内外分离模拟法，这样可以显著降低数值模拟对计算机硬件的要求。

Don not attempt to do something which you can not to do.

不要企图做那些办不到的事情。

The expression of CTGF and TNF-αweredetected by immunochemistry and the number of Clara Cells was calculated.

光镜下观察肺组织的病理变化，采用免疫组化染色观察肺组织中结缔组织生长因子和肿瘤坏死因子-α的表达和Clara细胞的数量。