查询词典 apparent depth

For example, the depth of mountain tundra soil profile was 75 cm, and apparent 14C ages was 1315 a; the depth of brown coniferous forest soil profile was 40 cm, and apparent 14C ages was 870a; the depth of lessive black brown soil was 120 cm, and apparent 14C ages was 5145 a.

这不仅是由于它们的生化性质及其化学组成不同而造成的，而且还因为土壤有机质分解与累积相互影响制约的结果。

At 135 mm depth and 0.28 m/sec speed, the biomimetic furrow opener surface with UHMWPE tubular ridges recorded 0.62 kN and 0.17 kW, while at 135 mm depth and 0.92 m/sec speed, the values were 0.91 kN and 0.82 kW. The experimental values of resistance force and power for the conventional surface furrow opener at 100 mm depth, and 0.28 m/sec speed were 0.72 kN and 0.20 kW, while at 100 mm depth and 0.92 m/sec speed, the values were 1.11 kN and 1.0 kW. At 135 mm depth and 0.28 m/sec speed, the conventional surface furrow opener recorded 0.93 kN and 0.25 kW, while at 135 mm depth and 0.92 m/sec speed, the values were 1.50 kN and 1.35 kW.

试验测试结果：当耕深100 mm和耕作速度0.28 m/sec时，实测的普通开沟器的土壤阻力和动力消耗分别为0.72kN和0.20kW；当耕深100 mm和耕作速度0.92 m/sec时，实测的普通开沟器的土壤阻力和动力消耗分别为1.11kN 和1.0kW；当耕深135 mm和耕作速度0.28 m/sec时，实测的普通开沟器的土壤阻力和动力消耗分别为0.93kN和0.25kW；而当耕深135 mm和耕作速度0.92 m/sec时，实测的普通表面开沟器的土壤阻力和动力消耗分别为1.5kN和1.35kW。

The phosphorus forms and BAP vary with horizontal and vertical positions. The total phosphorus, inorganic phosphorus, BAY, and iron-phosphorus contents were high at a depth of 0~20 cm at the first sampling point, and then decreased at 20-40 cm of depth. This shows that the potential release capacity of P at 0-20 cm of depth is higher. The concentrations of total phosphorus and inorganic phosphorus decreased at 0~20 cm of depth and increased at 20~40 cm of depth at the second sampling point, but BAY and Fe-P increased along with the depth consistently. This shows that the deeper layer at the second sampling point had a higher potential release capacity of phosphorus.

不同地点沉积物各磷形态和BAP的垂向变化有较大的差异。1号采样点的总磷、无机磷、铁磷和BAP质量比在沉积0~20 cm处较高，20~40 cm逐渐减小，说明0~20 cm内释磷潜力较大；2号采样点的总磷和无机磷质量比先减小，20~40 cm逐渐增加，而BAP和铁磷质量比随深度增加呈上升趋势，说明2点深层具有较大的释磷潜力。

Three expert systems for inversion were applied into practical engineering. Basing on the formulation of apparent resistivity in whole space, the curves of time vs. response which were gotten from practical exploring were transformed into the curves of depth vs. apparent resistivity by VC program. The data which were gotten from measurement line on working face in tunnel were transformed into the section map of depth vs. apparent resistivity. The result shows that expert system for inversion is feasible.

将三种反演专家系统应用于实际工程中，同时根据全空间视电阻率公式，采用VC编程的方法，将实际工程探测所得到的时间——响应曲线转化为深度——视电阻率曲线，将掌子面测线数据转化为深度——视电阻率断面图，对比两种计算方法的结果，说明反演专家系统在瞬变电磁反演中的可行性

The predicted values of resistance force and power for the conventional surface furrow opener at 100 mm depth and 0.28 m/sec speed were0.51 kN and0.14kW, while at 100 mm depth and 0.92 m/sec the values were0.98kN and0.88kW. At 135 mm depth and 0.28 m/sec speed, the conventional surface furrow opener recorded 0.70 kN and 0.20 kW, while at 135 mm and 0.92 m/sec speed, the values were 1.40 kN and 1.26 kW. The predicted values of resistance force and power for the biomimetic furrow opener surface with UHMWPE tubular section ridges at 100 mm depth and 0.28 m/sec speed were 0.45 kN and 0.12kW, while at 100 mm depth and 0.92 m/sec speed, the values were 0.73kN and 0.66 kW.

对于超高分子量聚乙烯材料仿生脊型非光滑结构表面，当耕深100 mm和耕作速度0.28 m/sec时，预测的仿生开沟器的土壤阻力和动力消耗分别为0.45kN和0.12kW；当耕深100 mm和耕作速度0.92 m/sec时，预测的仿生开沟器的土壤阻力和动力消耗分别为0.73kN和0.66kW；当耕深135 mm和耕作速度0.28 m/sec时，预测的仿生开沟器的土壤阻力和动力消耗分别为0.62kN和0.17kW；而当耕深135 mm和耕作速度0.92 m/sec时，预测的仿生开沟器的土壤阻力和动力消耗分别为0.91kN和0.82kW。

With the reaction time is variable speed integration of the equation fitting response curve Determine the apparent Michaelis constant (apparent MichaelisMenten constant, Kmapp) and the most apparent reaction rate (apparent maximal reaction rate, Vmapp).

用反应时间为自变量的积分速度方程拟合反应曲线确定表观米氏常数(apparent MichaelisMenten constant， Kmapp)和表观最大反应速度(apparent maximal reaction rate， Vmapp)。

The maximal depth model for single-pass milling process, the depth and surface roughness for plane surface are established. The milled profile of a single-pass milling of the jet can be modeled as a cosine curve of the form. Therefore, the maximal depth model for single-pass milling is established which indicates the quantitative relationship between the AWJ single-pass milling depth and the milling parameters.

假设磨料水射流单次铣削时的工件横截面形状为余弦曲线，建立了磨料水射流单次铣削的最大深度模型，分析了水射流压力、磨料流量、靶距、喷嘴横移速度、横向进给量和喷嘴直径及材料性能参数对单次铣削最大深度的影响规律。

The results indicate that multiple reflections are favorable to the increase of depth. When the focal position is above the surface, the absorptive intensity on the front decreases, so the cutting depth decreases. When the focal position is below the surface, the position on the front with the maximum power intensity is downward. The intensity distribution is toward the deeper position, the cutting depth increases. But if the negative focal distance is extremely big, the intensity of the deeper position attenuates sharply with the increase of focal radius and light distances, so the depth deceases.

正离焦切割时，前沿吸收的总激光功率密度减小，切割深度减小；负离焦切割时，最大激光功率密度值的位置下移，使得前沿功率密度分布朝着深部推进，切割深度增加，若负离焦量过大，表面光斑直径和光程增加，更深位置的功率密度减小，切割深度减小；随着激光功率增加、切割速度减小，则前沿弯曲程度减小，被激光直接照射的前沿部位增长，前沿吸收激光功率密度增加，切割深度增加。

In this paper, Newton iteration formula for computing normal depth and critical depth was put forward by mathematical transformation of uniform flow equation and critical flow equation of circular section tunnel. Then, the relationship between the corresponding central angle and the introduced parameters was analyzed. An approximate formula for angle was obtained according to optimal uniform approximation principle. Using this approximate formula as initial value of iteration formula, a direct formula for calculating normal depth and critical depth of circular section tunnel was established after its first iterative.

该文通过对圆形断面均匀流方程与临界流方程的数学变换，分别得到其正常水深与临界水深的牛顿迭代公式，同时，通过对正常水深与临界水深对应的中心角与引入参数之间关系的分析及数值计算，利用最优一致逼近原理分别得到了正常水深与临界水深对应中心角的近似计算式，并以此近似计算式为初值，用迭代方程进行一次迭代得到了圆形断面均匀流水深与临界流水深的直接计算公式。

To analyze the pseudo phenomena caused by migration velocity error, the paper firstly studied the depth error between post-stack migration and prestack migration caused by same velocity error, and found the depth error was only relative to velocity error and had no direct matter with methods of depth migration (post-stack migration or prestack migration). Then the paper did numerical simulation of a complex lenticular body model with wave-equation modeling and migration, and found that the velocity error could not only induce depth error, but also could change the modality of construction and the event of subjacent layers. Furthermore, it could change the frequency of reflective event. They are the pseudo phenomena caused by migration.

从分析偏移速度误差带来的各种假象出发，本文首先对比分析了速度误差对叠后深度偏移和叠前深度偏移的影响，发现偏移剖面的深度误差仅与速度模型的误差有关系，与具体的偏移方法没有直接的关系；然后对一个复杂的透镜体模型进行了波动方程叠后正演和偏移计算，详细地讨论了不同的速度误差带来的各种假象，发现速度误差不仅会带来深度误差，而且会造成构造体的形态变化，下覆地层同向轴的扭曲，还可能引起地层同向轴的频率发生变化，给资料解释带来一定的假象。

I hope that this success is just the first in a long series.

我希望这只是成功的开始。

Three dimensional stresses on the interface of tire and soil, tire deflection and soil sinkage are measured.

测试轮胎——沙土界面上的三向应力、轮胎变形和沙土沉陷；建立考虑剪切应力对沙土承载特性产生影响的车轮牵引性能预测模型；分析车轮作用下土壤的纵向稳定性。