- 更多网络例句与静止摩擦相关的网络例句 [注：此内容来源于网络，仅供参考]
-
Though it is a long history of the research on static friction, many problems, such as relationship between static friction and static contact time, the relationship between static friction and load, and the prediction of static friction coefficient have not yet fully studied.
虽然静摩擦的研究历史很悠久，但仍有一些问题没有解决，如静摩擦与静止接触时间的关系，静摩擦与载荷的关系，以及静摩擦系数的预测等问题。
-
Therefore, the torque required to open the gate valve required torque than the closure of large, in addition, for a pair of contact between the sealing surface, the Non Rising Stem Resilient Seated Gate Valves coefficient of static friction between them than the dynamic friction coefficient, to make them from the static state generate the relative movement is required to exert greater force to overcome the static friction; due to temperature changes, so that the sealing surface pressure between the larger, need to overcome the static friction force also will be bigger, so that when you open the valve on the stem nut on the sometimes increase the torque exerted a lot.
所以，开启闸阀所需的力矩比关闭闸阀所需的力矩大，此外，对于一对互相接触的密封面来说，它们之间的静摩擦系数也比动摩擦系数大，要使它们从静止状态产生相对运动，需施加较大的力以克服静摩擦力；由于温度变化，使密封面间的压力变大，需要克服的静摩擦力也随之变大，从而使开启闸阀时，对阀杆螺母上施加的力矩有时会增大很多。" Moment analysis of valve operation "是由中国闸阀网提供的国际阀门新闻，译文仅供参考。另外，中国闸阀网还提供相关产品搜索：闸阀型号、闸阀价格、闸阀技术、闸阀新闻、闸阀生产商等。
-
Afterwards, we propose a new constant coefficients measurement method in dynamic equation of robot manipulators, this measurement method includes three groups of experiments: group one, let each joint of robot manipulator keep static to measure the constant coefficients in gravity term of dynamic equation and Coulomb frictional torque, group two: let only one joint of robot manipulator move at a constant velocity to measure the viscous frictional coefficient and constant coefficients in effective inertia of dynamic equation, group three: let only one joint of robot manipulator move at constant acceleration at a time to measure constant coefficients in Coriolis and centrifugal term and coupling inertia of dynamic equation.
让操作器单个关节恒速运动，在对驱动系统中传动机构，减速装置和电感系数综合考虑的基础上，这组实验对粘滞摩擦系数及有效惯量中常数系数进行测量。这种测量方法只要求旋转关节的驱动电机施加恒定电压，回转关节驱动电机施加正弦波电压。3。让操作器单个关节恒加速运动，这组实验测量动力学方程中哥氏力、离心力项和耦合惯量项中的常数系数，这种测量方法只要求单个关节匀加速运动，而其它各关节保持静止，这种测量方法虽然要求关节匀加速运动，但不必进行关节角加速度检测，而只需进行关节角位移和角速度检测即可，输入量直接给定为输入电压。
-
"Kinetic friction arises between surfaces in relative motion, static friction acts between surfaces at rest with respect to each other"
动摩擦力存在于相对运动之表面间，静摩擦则存在于静止的表面间，。
-
The results show that the plasticity zone and dynamically quiescent layer become fine equiaxed recrystallisation under the thermo-mechanical effect, the grains in the heat-affected zone grow up because of the effect of friction heat. When the rotation speed is 2 500 r/min and the welding time is 12 s, good joint is achieved, and the tensile shear strength of the joint reaches 9.24 kN. The tensile shear strength of spot increases with increasing tool rotation speed, with increasing welding time, the strength increases first, while then reduces. The microhardness of plasticity zone is high, but is slightly lower than that of the base metal, the minimum value of microhardness is in the heat affected zone. When the energy input of joint is high, the fracture type of spot is mode Ⅰ, and the tensile shear strength is high; on the contrary, when the energy input of joint is less the fracture type of spot is mode Ⅱ, and the strength is low.
结果表明：塑性区和动态静止层的晶粒在热和力作用下发生动态再结晶形成细小的等轴晶，热影响区的晶粒在摩擦热作用下长大变粗；搅拌头旋转速度为2 500 r/min，焊接时间为12 s时，可以获得力学性能较好的焊点，焊点的剪切强度达到9.24 kN；焊点的剪切强度随搅拌头旋转速度的增大而增大，随焊接时间的延长先增大后减小；塑性区的显微硬度较高，但略小于母材，接头显微硬度的最小值分布在热影响区；焊点热输入量较多时，接头为Ⅰ型断裂，焊点的剪切强度较高；焊点热输入量较少时，接头为Ⅱ型断裂，焊点的强度较低。
- 更多网络解释与静止摩擦相关的网络解释 [注：此内容来源于网络，仅供参考]
-
angle of repose：静止角;休止角
angle of internal friction 内摩擦角 | angle of repose 静止角;休止角 | angle of rupture 破裂角
-
coefficient of friction resistance：摩阻系数
coefficient of friction of rest | 静止摩擦系数 | coefficient of friction resistance | 摩阻系数 | coefficient of frictional wear | 磨损系数