轴承环

词组短语

bearing ring · bearing collar · guide track

与轴承环相关的网络例句 [注：此内容来源于网络，仅供参考]

The bearing ring grooves are circular arcs made slightly larger than the radius of the ball.

轴承环槽的圆弧了略高于球的半径大。

By means of analyzing the influence of OD surface roundness error on the outer raceway of bearing ring, the processing method of bearing on internal grinder electromagnetic centerless clamper was improved, the influence of roundness error on outer raceway was decreased, meanwhile, the product quality was raised with less waste products.

通过分析轴承环外径表面圆度误差对轴承环外滚道的影响，改进了轴承在内圆磨床电磁无心夹具上的加工方法，降低了轴承环外径定位表面圆度误差对轴承环外滚道的影响，提高产品质量，达到了降低废品损失的目地。

When grinding the bearing ring, the outside diameter of it was taken as locating datum to process the outer raceway with the assistance of electromagnetic centerless clamper.

轴承环磨削过程中，以轴承环外径作为定位基准，在电磁无心夹具上磨削轴承环外滚道。

This Bearing consists of 3 kinds of grooved washer bearing rings, 2 kinds of cage and ball assembly.

这种轴承由3洗衣机槽轴承环，2架和球组装种。

This contributes to the rigidity of the bearing and a precise radial guidance of the shaft. For special applications, full-complement cylindrical roller bearings are employed. The cylindrical roller bearing designs are shown in Figures 1.20 and 1.21.The designs of cylindrical roller bearings are distinguished by the arrangement of the lips. Design NU (Figure 1.21b) has two lips on the outer ring, the inner ring being lipless. In design N (Figure 1.21a), the inner ring has two lips, the outer ring has none. Cylindrical roller bearings of designs NU and N are applied as floating bearings because the rollers can freely shift on the lipless ring in the axial direction. Cylindrical roller bearings NJ (Figure 1.20) have two lips on the outer ring and one on the inner ring; they can take up axial forces in one direction. Design NUP (Figure 1.21d) is installed as a locating bearing to sustain frequently reversing axial forces.

这可以提高轴承的刚度，和主轴精密的径向引导，对于特别的运用，密排的圆柱滚子轴承被运用，圆柱轴承的图样在图。20和1.21展示圆柱滚子轴承图样由挡边的不知来区分，图样NU(图1.21b)在外圈有两个挡边，内圈无挡边，在图样N中内圈有两个挡边，外圈无挡边，图样NU和U所示的圆柱滚子轴承可制作浮动轴承因为滚子能够在轴向无挡边环上自由的移动，圆柱滚子轴承NG在外圈上有两个挡边，内圈上有一个，它们能够在某个方向上承受轴向力，图样NUP（图1.21d）被用来安装在一个保持经常扭转轴向力的固定轴承上。

Appraisal committee thinks, the bearing core response that place of this task group develops disassembles implement can disassemble continuously 5 to 8 bearing core won't overheat, the axis after disassemblingBear the surface did not appear the scat......

鉴定委员会认为，该课题组所研制的轴承内环感应拆卸器可连续拆卸5至8个轴承内环而不会过热，拆卸后的轴承表面未出现。。。。。。

Bearing ring rotating components of the noodle and roll surface roughness is usually 1 / 10 μm, so a smooth surface of the pollutants is very sensitive to damage.

轴承环转动面和滚动元件的表面粗糙度通常为1/10 μm，如此光滑的表面对污染物造成的损坏非常敏感。

Mechanical seal assembly: In the dynamic and static loop mirror coating on the 20th floor cleaner lubricants; add lubricant bearing guided, first gently positioning ring static load bearing guide; longer shaft add the oil, the mechanical seal part of the dynamic ring gently into the shaft, the hand-push retractable seal ring should be able to freely (Note that dynamic and static part of the anti-ring to the assembly site to be in place).

机械密封装配：在动、静环镜面上涂一层洁净的20号润滑油；导轴承座抹上润滑油，先把静环轻轻定位装入导轴承座；再在泵轴上抹上润滑油，把机械密封的动环部分轻轻装渗透泵轴上，用手轻推密封环应能伸缩自如（注意动、静环部分的防转部位需装配到位）。

Mechanical seal assembly: In the dynamic and static loop mirror coating on the 20th floor cleaner lubricants; add lubricant bearing guided, first gently positioning ring static load bearing guide; longer shaft add the oil, the mechanical seal part of the dynamic ring gently into the shaft, the hand-push retractable seal ring should be able to freely (Note that dynamic and static part of the anti-ring to the assembly site to be in place).

机械密封装配：在动、静环镜面上涂一层洁净的20号润滑油；导轴承座抹上润滑油，先把静环轻轻定位装入导轴承座；再在泵轴上抹上润滑油，把机械密封的动环部分轻轻装入泵轴上，用手轻推密封环应能伸缩自如（注意动、静环部分的防转部位需装配到位）。

Mechanical seal assembly: In the dynamic and static loop mirror coating on the 20th floor cleaner lubricants; add lubricant bearing guided, first gently positioning ring static load bearing guide; longer shaft add the oil, the mechanical seal part of the dynamic ring gently into the shaft, the hand-push retractable seal ring should be able to freely (Note that dynamic and static part of the anti-ring to the assembly site to be in place).

机械密封装配：在动、静环镜面上涂一层洁净的20号润滑油；导轴承座抹上润滑油，先把静环轻轻定位装入导轴承座；再在泵轴上抹上润滑油，把机械密封的动环部分轻轻装入泵轴上，用手轻推密封环应能伸缩自如（注重动、静环部分的防转部位需装配到位）。

与轴承环相关的网络解释 [注：此内容来源于网络，仅供参考]

snap ring：卡环

精和,是止动环,卡环(Snap Ring)的专业制造厂家,多年来致力于止动环卡环的生产和开发. 主要生产IS0464;GB/T305;DIN5417等标准系列的SP;NR;WR;WRE;BR;AR;SB止动环、卡环;以及FMG;MR;SL;TR;等轴承卡簧;电机轴承径向止动环;轴承锁圈等产品.

Bearing spacer：轴承隔离圈, 轴承定距环

shaft collar 轴环 | bearing spacer 轴承隔离圈, 轴承定距环 | double volute 双蜗壳

bearing cages：轴承环

承载力:bearing capacity | 轴承环:bearing cages | 球轴承:ball bearing

bearing ring：方位圈轴承环

bearing ring 方位圈;轴承套圈 | bearing ring 方位圈轴承环 | bearing ring 轴承环

oscillation bearing ring：摆动轴承环

oscillation bearing;摆动轴承 | oscillation bearing ring;摆动轴承环 | oscillation clearance;摆动间隙[距离]

thrust collar bearing：推力环轴承

thrust collar ==> 推力环,止推环,止推轴承定位环 | thrust collar bearing ==> 推力环轴承 | thrust component ==> 推力分量

bearing collar：轴承环

bearing circle 方向盘 | bearing collar 轴承环 | bearing cone 锥形轴承内环

bearing collar：轴承环,推力头

bearing carrier,轴承座 | bearing collar,轴承环,推力头 | bearing cover,轴承盖

collar thrust bearing：环领止推轴承

环境负荷 environmental load | 环领止推轴承 collar thrust bearing | 环领轴承 collar bearing

oil ring bearing：油环润滑轴承,油环轴承

oil-return device ==> 回油装置 | oil-ring bearing ==> 油环润滑轴承,油环轴承 | oil-ring guide ==> 油环导槽