- 更多网络例句与轴上的相关的网络例句 [注：此内容来源于网络，仅供参考]
-
The kinematics of precision centrifuge isanalyzed in Chapter 2 adopting Homogeneous transformation and vector analysis.The calculating formulae of centripetal acceleration generated by precision centrifugeand acceleration acting on input axis, output axis and pendulous axis of accelerometerare deduced in theory under various conditions.
论文第2章首先用齐次变换法和矢量分析法对精密离心机的运动学进行了分析，从理论上推导出离心机产生的向心加速度的计算公式，以及各种条件下作用在加速度计输入轴、输出轴和摆轴上的加速度。
-
A transmission for vehicles is provided with a plurality of drive gears, an input shaft connected to the drive shaft of an engine, an output shaft disposed parallel to the input shaft, a driven gear which meshes with each drive gear and is rotatably disposed on the output shaft, a synchromesh mechanism which has a sleeve movable in the axial direction of the output shaft, is engageable with a side portion of the driven gear, and couples the driven gear to the output shaft, and a parking gear formed integrally with the sleeve of the synchromesh mechanism.
用于车辆的传动装置配备多个驱动齿轮；连接到发动机的驱动轴的输入轴；与输入轴平行设置的输出轴；与每个驱动齿轮啮合并且可转动地设置在输出轴上的被驱动齿轮；具有可沿输出轴的轴向移动的套筒，可与被驱动齿轮的侧部啮合并且将被驱动齿轮连接到输出轴的同步啮合机构；和与同步啮合机构的套筒一体形成的泊车齿轮。
-
Hydraulic forces applied on the agitator are simplified as a main moment and a main force on the agitating shaft, Initial decentration of agitator is determined based on the balance standard. The dynamic responses, such as fluctuating bending stresses and dynamic deflections, of the agitating shaft under no-liquid and normal working conditions are studied.
将搅拌器上的流体作用力简化为一个主矩和主矢；为考虑作用在搅拌轴上的惯性力效应，根据平衡精度预设搅拌器的初始偏心；在转子动力学软件ROTOR中建立搅拌轴的梁盘模型，分别计算了搅拌轴在空载和搅拌工况下的动力响应，并进一步讨论了动力响应与工作转速、轴径和轴长的关系。
-
When the parameter matching of the wheel location is improper, namely, the matching between the wheel toe-in and the wheel camber angle is ill-suited, abrasion of the two wheels of the same steering axle is inside or outside simultaneously, because of wheels sideslip. However, when double-front-axle steering system failure take place, abrasion of the two wheels of the same steering axle is in the same side, and that, tyre abrasion direction of front and back steering axles is rightabout. That is to say, if tyre abrasion of front steering axle lie in the left side, tyre abrasion of back steering axle lie in the right side to a certainty, which is the rule of tyre abrasion of double-front-axle steering automobile.
当定位参数匹配不当时，同一转向轴上左右车轮的磨损部位都在内侧或外侧，原因是左右车轮在滚动的同时还要产生相向或反向侧滑；而双前轴转向汽车前、后转向轴引导汽车转向方向不一致时，同一转向轴左、右车轮的磨损部位都在同一侧，而且前、后转向轴上的车轮偏磨损方向正好相反，即如果前转向轴左、右车轮磨损部位在左侧或右侧，那么后转向轴左、右车轮磨损部位就在右侧或左侧，这是双前轴转向汽车特有的轮胎磨损规律。
-
Change tradition tee joint into abutment joint , resulting in clear increase of fatigue strength of welding line of oscillating axle of press and safety service life of press hence a worthwhile method for corresponding personnel .
文章提出了提高压力机的摇摆轴焊缝的疲劳强度的技术措施，即将传统的在光轴上的&T&形接头改为台阶轴上的对接接头，可显著提高压力机的摇摆轴焊缝的疲劳强度及压力机的安全使用寿命，此方法值得有关人员借鉴。
-
The sliding gear assembly consists of sliding shaft, sliding gear and sliding clutch. The sliding shaft coaxial with the driving shaft has one end stretched into the axial hole on one end one the driving shaft and the other end supported on the front end casing; and the driving shaft is fixed axially onto the pedestal.
滑动齿轮组件由滑动轴、连接在滑动轴上滑动齿轮、连接在在滑动轴上的滑动离合器组成；滑动轴与传动轴同轴；滑动轴的一端的伸入在传动轴的一端沿轴向所开的孔内，另一端支撑在前端壳体上；传动轴在轴向被固定在底座上。
-
Mechanical transmission: the diesel engine, through four B-type belts, transmits power to the input shaft via clutch.
机械传动：柴油机通过四根B型皮带经离合器将动力传到输入轴，经I轴的双联齿转Z1、Z2，Ⅱ轴的Z3、Z4、Z5三个齿轮以及Ⅲ轴上的双联齿轮Z7、Z8，Ⅳ轴上的Z9、Z10，使输出轴得到五种速度，又通过齿轮Z9、Z10、Z11将动力分别或同时传给转盘和升降机。1。
-
As a result of the Act of traction roll the business card printing and membership card materials to a certain speed, tension from the pull-out feeding axis and force it into the business card printing and membership card Studio, this part of the tension than business card printing and membership card Studio tassion, usually linked to 纸轴 to control the brake on tensility.
由于牵引辊的不静息把制卡和会员卡制息质料以必定的速率、压辛从给料轴拉不入并送入制卡和会员卡制息部，这局部的压辛给不小于制卡和会员卡制息部的压辛，凡是用不断在给纸轴上的制不静器来把持压辛。
-
Curve and the x, y-axis intersection (a, 0),(0, b) where a curve is called the intercept in the x-axis; b is called the curve y axis intercept .
曲线与x、y轴的交点（a，0），（0，b）其中a叫曲线在x轴上的截距；b叫曲线在y轴上的截距。
-
Curve and the x, y-axis intersection (a, 0),(0, b) where a call in the x-axis intercept curve; b is called the curve y axis intercept .
曲线与x、y轴的交点（a，0），（0，b）其中a叫曲线在x轴上的截距；b叫曲线在y轴上的截距。
- 更多网络解释与轴上的相关的网络解释 [注：此内容来源于网络，仅供参考]
-
countershaft：副轴
概念如下图,动力从绿色箭头处输入经A齿轮传到B齿轮带动副轴 (countershaft) 及副轴上的HGR齿轮. 齿轮FE滑动於驱动轴 (drive shaft) 上. 若将F向左滑动,藉著齿状结构使AF直接连结,驱动轴得到和输入轴一样的转速与扭力. 若将F向右滑动,
-
shaft horsepower：轴马力,轴功率 [在压缩机轴上测得的马力消耗]
Shaft bearing 轴承 | Shaft horsepower 轴马力,轴功率 [在压缩机轴上测得的马力消耗] | Shafting 轴系,传动轴
-
PIVOT CUP：枢轴窝,桥底座上配合悬轴支点的部分
74、 PADS 护具 | 75、 PIVOT CUP 枢轴窝,桥底座上配合悬轴支点的部分. | 76、 PLATFORM 平台
-
axile placentation：中轴胎座式
axil | 叶腋 | axile placentation | 中轴胎座式 | axile | 轴的, 轴上的
-
axile：轴的, 轴上的
axile placentation | 中轴胎座式 | axile | 轴的, 轴上的 | axilemma | 轴索鞘, 轴索膜
-
axilemma：轴索鞘, 轴索膜
axile | 轴的, 轴上的 | axilemma | 轴索鞘, 轴索膜 | axilla | 咯肢窝, 腋窝
-
epaxial：轴上的
epaulet 毛肩片 | epaxial 轴上的 | epaxialmuscle 轴上肌
-
epaxial：轴上的; 轴后的 (形)
epaulet 肩章; 肩饰 (名) | epaxial 轴上的; 轴后的 (形) | epee 重剑 (名)
-
becking：(轮箍环的)辗轧 (圆环零件在心轴上)扩孔锻造
becking bar || 辗锻用心轴 | becking || (轮箍环的)辗轧 (圆环零件在心轴上)扩孔锻造 | Beckmann thermometre || 贝克曼温度计
-
Y Of Point：单位在Y轴上的坐标
X Of Point 单位在X轴上的坐标 | Y Of Point 单位在Y轴上的坐标 | Camera Field Of Camera Object 镜头对象的视野