焊波

词组短语

weld mark

与焊波相关的网络例句 [注：此内容来源于网络，仅供参考]

This paper analyzes the characteristic of the Power Factor Correction of arc welding inverter power source , introduces the 12-pulse converter based on delta-type autotransformer connection into arc welding inverter power source ,and its configuration, design scheme and theory on PFC.

分析了弧焊逆变电源功率因数校正技术的特点，阐述了弧焊逆变电源中基于差接三角形自耦变压器十二脉波整流电路的原理与设计及其功率因数校正机理。

In ultrasonic inspection of butt weld s, interfering echoes, such as corner echo, hill-shaped echo, etc.

在对接焊缝超声波探伤中，荧屏上常会出现一些影响缺陷判别的干扰回波，如焊角回波、"山形回波"等。

The structure is complex at the joint root of welding pipelines, where exist cold solder joint and cracks.

管道焊缝根部区域结构复杂，是未焊透和裂纹的产生处，反射回波杂乱，是超声波检测的重点也是难点。

Uses completely imports the thermostable nylon (PA66) raw material to add the fire protection textile fiber fine note to become again, has does not plate the electricity, artistic, thermostable and the antiseptic property is good, can when welds and the wave front welds the body had guaranteed that does not distort on machine the board not crookedly, quality assurance, reasonable price!

全部采用进口耐高温尼龙（PA66）原料再加防火纤维精注而成，具有不镀电、美观、耐高温及防腐性能好，能在焊接及过波锋焊时体保证在机板上不变形不歪斜，固定在PCB板上！质量保证，价格合理！

Focusing on the normal inverter's dynamic characteristics which can not satisfy the requirement of reducing current quickly before the time of rupturing of the bridge, a new current wave controlling method for short circuit transfer CO 2 welding using satiable inductor is put forward in this paper.

本文针对普通CO2焊逆变电源的动态性能不能满足短路过渡CO2焊波控方法的要求，焊接电源难以实现在液桥爆断前迅速减小电流的问题，提出了一种在波控方法中采用可饱和电感作为CO2逆变焊机续流电感的方案。

Equivalent stress nearby the spot weld is greater other placeand there is obvious stress concentration.

由应力分布情况得出，在焊点附近的等效应力较大，存在明显的应力集中现象，同时由于折流缝焊的存在，增加了波面传热板强度。

In the square wave current welding,the inductance is very important to influence the fomation of square wave A.

在方波交流焊中，电抗器的电感量对方波的形成及电弧的稳定性有着很大的影响。

In view of the development about the certain airborne radar antenna array,considering the structural features of antenna array,analyse the cruces in manufacturing of feed cavity and radiant plate,and present the corresponding solution by mainly dealing with precise positioning style,delicate clamp design,error distribution and compensation method,high speed machining technology design,machining simulation and program optimizing.

某机载雷达平面裂缝阵列天线的单面阵如图1所示。该面阵布置多路裂缝线源，共分布384处长度各不相同的辐射裂缝，每一路线源均由脊型波导口单独馈电。面阵由辐射板和馈电腔两个零件组成，采用整体钎焊成形。线源结构为非对称单脊共线形式，即在普通单脊波导的两侧与辐射裂缝相对应的位置上布置不对称的凹台。

In addition, the analyses of weld surface ripple and microstructure with three current waveforms have indicated that the high frequency wave group modulated by low frequency GTA welding has the advantage of both the low frequency in which the heat input of the weld pool is easily controlled and high frequency GTA welding in which the arc is energy—concentrated and stiff.

另外，通过对高频脉冲焊、低频脉冲焊、低频调制高频方波群焊不锈钢焊缝表面形貌分析表明，低频调制高频方波群焊综合了低、高频GTA焊的特点。

3L terminations are suitable for all wave and reflow soldering systems.

三的端面适合波焊及回焊系统。

与焊波相关的网络解释 [注：此内容来源于网络，仅供参考]

dipole antenna：半波天线,双极天线

热浸硬焊 dip brazing | 半波天线,双极天线 dipole antenna | 杓 dipper

weld ripples：焊波

weld quality 焊接质量 | weld ripples 焊波 | weld strength 焊接强度

sigma welding：金属惰气电弧焊

有义波 sigificant wave | 金属惰气电弧焊 SIGMA welding | 信号 signal

skipping：漏焊

如此将可对贴装零件脚之填锡补锡大有帮助,并可减少背风坡处的"漏焊"(Skipping)现象. 当然在双波的先强劲与后温柔的不同作用下,整体焊锡性也将会更好. (2)当板面进入锡波中心处的"传热区"(Heat Transfer Region)时,在大量热能的推动下,

up hill welding：上向焊

上相微乳|upper phase microemulsion | 上向焊|up hill welding | 上行波|upgoing wave

longitudinally welded：纵焊的

longitudinally polarized geophone 轴向偏振拾波器 | longitudinally welded 纵焊的 | longitudinally-welded pipe 直缝焊接管

wave soldering：波焊

PCB之发展已数十年,然近年来,在轻薄短小的趋势下加上电子组装导入无铅制程生产 (Lead Free Process) 后,不论回焊(Reflow Soldering)与波焊(Wave Soldering) 组装温度提高,所增加的热应力对传统PCB潜在的影响更为严重,

rippled surface：焊波表面

ripple weld 鳞状焊缝 | rippled surface 焊波表面 | riser 冒口

one-third highest wave：三分之一最高[平均]波,有义波

"单面电热气体电弧焊","one-side electro gas arc welding" | "三分之一最高[平均]波,有义波","one-third highest wave" | "直流锅炉","one-through boiler"

progressive wave winding：行波式绕组

progressive wave tube ==> 行波管 | progressive wave winding ==> 行波式绕组 | progressive welding ==> 前进焊,分段焊接