- 更多网络例句与烧蚀相关的网络例句 [注：此内容来源于网络，仅供参考]
-
According to the appraisal of ablate resistant resin,the properties and application of modified phenolic resin s and PAA etc new ablate resistant resin are Introduced.
根据对耐烧蚀树脂基体的评价，介绍了改性酚醛树脂及芳基乙炔等新型耐烧蚀树脂基体的性能及其应用概况，并指出高性能、低成本是今后耐烧蚀树脂基体的发展方向。
-
A new theoretical model has been developed to describe the whole ablation process,including the effect of dynamic absorptance and evaporation.
提出了描述整个飞秒多脉冲激光烧蚀过程的物理模型，模型考虑了多脉冲烧蚀的新的特点，考虑靶材吸收率随温度的变化和蒸发效应，建立了激光烧蚀不同阶段的热传导方程，给出了相应的定解条件。
-
The ablation properties were tested in an oxyacetylene torch. The phase composition and morphology of the composites were investigated by XRD and SEM, respectively.
用氧乙炔烧蚀测试材料的烧蚀性能， XRD测试材料烧蚀前后的物相组成，采用SEM观察材料的微观形貌。
-
The evaporation of ZrO2 will absorb heat and relieve erosion from oxyacetylene flame on the ablated surface of the specimen, and also accelerate the mass loss of the specimen, which leads to the decrease of the linear ablation rate and increase of mass ablation rate of the composites.
产物ZrO2的蒸发吸收了材料烧蚀表面的热量，减缓了火焰对烧蚀表面的冲蚀，材料的线烧蚀率减小，然而， ZrO2的蒸发会增加材料的质量损失速度，导致材料的质量烧蚀率增大。
-
Resonant laser ablation is a two-step process, occurring within a pulse of a tunable laser, in which the leading edge of the laser pulse ablates the surface of the solid sample to produce neutral atoms or molecules that are then resonantly ionized by the trailing edge of the same pulse.
共振激光烧蚀技术是指发生在同一激光脉冲时间内的两步过程，它是指用波长可调谐的染料激光取代固定波长输出的激光，并调谐激光输出波长实现所研究原子或分子电子态之间的共振跃迁，激光单次脉冲的前沿对样品进行烧蚀，烧蚀的物质在激光光束内形成粒子气团，同一次激光脉冲的后沿实现对气相原子或分子的共振电离。
-
BSpatial characterization of laser induced Cu plasma in air with different laser focusing distancesThe plasma spectra induced by pulsed laser ablation of copper target are measured. By adjusting the distance of the len-sample, the spectrum of air spark plasma、 Cu plasma and the reciprocity of both plasmas are analysed. From the result, it has been shown that the focusing of the laser beam has an important infunence to analyse the properties of the sample.
b 不同的激光焦点位置产生的等离子体光谱的空间特性研究激光烧蚀置于空气中的Cu靶产生等离子体，通过调节透镜与Cu靶的距离，本文观测了激光烧蚀空气产生的空气火花等离子体、激光直接烧蚀铜靶产生Cu等离子体以及空气火花等离子体与Cu等离子体相互作用等不同情况下的激光诱导击穿发射光谱，激光束焦点的位置在分析材料性质的过程中有着重要的影响。
-
Based on researchful results of two former students, we take the influences of thermochemistry reaction, mutual disturb and unsymmetrical instance into account. Secondly, the paper simulates the transient thermal response of projectile according to the simulation software, and discuss the ablation regulation when the projectile is in different initial velocity, in different shape, in different angle of attack condition and in different material condition. Thirdly, the effect on the aerodynamic characteristic and the outer ballistic characteristic after the ablation of hypersonic projectile has been analyzed.
在前面两位师兄研究成果的基础上，研究了超高速弹箭组合体在考虑热化学反应、存在攻角影响下的的气动加烧蚀数学模型；然后对不同条件下的烧蚀过程进行计算，分析和总结出在不同外形和不同材料条件下弹体和弹翼的烧蚀规律；紧接着分析了在不同的烧蚀情况下，它对飞行中弹箭的气动力和外弹道特性的影响，从而为今后的超高速弹箭设计提供指导和帮助。
-
An experiment on forming of cross-hatch on the ablation material surface has been done under the condition of Mach 5 and tur-bulent boundary layer regime.Artifitial disturbances created by randomly setting several pins along a line perpendiculer to the flow direction have shown stochastical character of local cross-hatch and independence of global orderly structure,therefore the pattern appeared fractal behavior.
在外流M＝5湍流边界层状态下，模型为170×300mm￣2蜂蜡平板上进行了烧蚀花纹图案生成的实验研究，通过实验证明了人工安置干扰源并不影响烧蚀材料表面花纹的有序结构，对大面积烧蚀花纹的分析表明，局部花纹结构具有随机性质，因此烧蚀花纹具有分形结构的特性，用分形方法可以大致模拟花纹生成图案。
-
The charring layer is easy to exfoliate when the combustion gas ablates the EPDM insulation at a certain angle.
结果表明，在不同烧蚀时间内，EPDM绝热层的烧蚀率表现出不同特征，EPDM绝热层烧蚀率与燃气流量成正比关系，燃气以一定角度侧向烧蚀绝热层时，炭化层极易脱落。
-
The heavier the ablation is, the faster attenuation the ablating acoustic spectrum has.
烧蚀程度越大，与烧蚀相关的烧蚀声峰衰减越强烈，烧蚀声峰的上升时间约为400 μs。
- 更多网络解释与烧蚀相关的网络解释 [注：此内容来源于网络，仅供参考]
-
ablation factor：烧蚀因素
ablation characteristics 烧蚀特性 | ablation factor 烧蚀因素 | ablation front 烧蚀正面
-
ablation characteristics：烧蚀特征
ablation characteristics|烧蚀特征 | ablation of melting body|熔融物体的烧蚀 | ablation-product radiation|烧蚀生成物的辐射
-
ablation characteristics：烧蚀特性
ablating heat shield 烧蚀热防护 | ablation characteristics 烧蚀特性 | ablation factor 烧蚀因素
-
ablative polymer：烧蚀性聚合物
ablative material 烧蚀材料 | ablative polymer 烧蚀性聚合物 | ablative-type protective coating 烧蚀型保护层
-
ablative mechanism：烧蚀机制
ablative material | 烧蚀材料 | ablative mechanism | 烧蚀机制 | ablative mode of protection | 烧蚀防护法
-
ablative material：烧蚀材料,烧蚀剂
ablative cooling material 烧蚀冷却材料 | ablative material 烧蚀材料,烧蚀剂 | ablative recording 冲蚀记录
-
ablator：烧蚀挡板;烧蚀体;烧蚀剂
ablative-type protective coating 烧蚀型保护层 | ablator 烧蚀挡板;烧蚀体;烧蚀剂 | ablaze 着火
-
charring ablator：炭化烧蚀体,炭化烧蚀材料
charred coal | 焦炭,焦煤 | charring ablator | 炭化烧蚀体,炭化烧蚀材料 | charring plastic | 焦化塑料
-
ablative leading edge：烧蚀前缘
ablative heat protection 烧蚀防热 | ablative leading edge 烧蚀前缘 | ablative mechanism 烧蚀机理
-
ablation of radomes：雷达天线罩的烧蚀
ablation of a subliming solid || 升华固体烧蚀 | ablation of radomes || 雷达天线罩的烧蚀 | ablation performance index || 烧蚀性能指数