开切眼

词组短语

through cut · open-off cut · first cut

与开切眼相关的网络例句 [注：此内容来源于网络，仅供参考]

According to the characteristic of the open-off cut s,we have improved the structure of retrievable cement metal bolts so that it can be used in open-off cut s.

针对煤矿开切眼巷道的特点，对可回收水泥金属锚杆结构进行改进，使其能够在开切眼巷道中使用。

The same set of ductile-rheologic shear deformational augen granite samples in the Yunkai uplifted area are measured by whole-rock Sm-Nd, Rb-Sr isotopic dating system method, obtaining respectively 1414±68Ma for Sm-Nd isochron age and 490±36Ma for Rb-Sr isochron age. These ages are respectively interpreted as the time of the granitic rock formation and the time of the tectono-thermal event of ductile-rheologic shear partial melting in Caledonian, indicating that the orogeny not only took place in Caledonian, but also the more important tectono-magmatic orogeny in the late Mesoproterozic Era and can be compared with the time of global Grenville orogeny.

对云开核部韧性-流变剪切变形眼球状花岗岩石样品进行了全岩Sm-Nd、Rb-Sr同位素年龄测定，获得1414±68Ma的Sm-Nd等时线和490±36Ma的Rb-Sr等时线年龄，它们分别代表这套花岗岩的形成时代和加里东期韧性-流变剪切部分熔融构造热事件发生时间，表明云开地区不仅在加里东期发生造山运动，而且在中元古晚期发生了更为重要的构造—岩浆造山运动，其时代与全球性的格林威尔造山运动时间可以对比。

The paper articulates the drilling fluids techniques employed for drilling huge gravels, large gypsums in deep wells, long shales, high pressure brines under high bottomhole temperature in extreme deep wells. This paper also discusses how to determine mud density for the fourth spudding, how to optimize mud addi...

详细介绍了该井大井眼巨厚砾石层、深井段巨厚盐膏层、第三系大段泥岩井段、高压盐水层及超深井高温条件下的钻井液工艺技术并对四开钻井液密度的确定、钻井液处理剂的优选和五开井段钻井液粘切的要求进行了探讨。

The mine open-off cut should be very safety because it is a wide-spanned place where the mining facilities are located.

采煤工作面的开切眼不仅跨度大，而且是采煤设备安装的场所，对于空间的安全有较高的要求。

When I'm satisfied with the general volume a shell modifier helps me to give thickness to the piece. In this phase, I don't usually bother that much about every single rivet, hole or cut, I just try to develop a good quad topology of the main volumes. Of course the topology is done by taking count of the main cuts and holes, but the rest can be done easily with a normal or bump map. It's up to you to decide how much a single detail is worth to be modeled or can it be put into a bump map. I usually adopt a "comfortable" criteria...it means that if something looks tricky to me to be carved or extruded into an existing geometry I usually put it into a normal map. When you make something for production, you don't usually have much time to model everything, so you need to set priorities.

当我对整个盔甲的体积感满意之后，一个shell修改器就可以帮我给整个盔甲添加厚度，在这个阶段，我通常不会考虑太多那些细小的铆钉，洞眼或者切边，我只是给整个的模型确立一个好的四边形拓扑结构，当然拓扑是通过重视主要的切割和打洞来形成的，但其余那些细小的部分可以用一个normal 或者bump贴图很容易地模拟出来，这由你来决定到底一个细节是值得建模还是放到一个bump贴图里面，我通常采用一个&舒服&的标准，也就是说，如果有什么东西对我来说，在已有模型上再挤出或者开洞是非常麻烦的，那么我就通过Normal贴图来表现，而当你为商业生产制作模型时，你通常都没有足够的时间来把任何东西都建出来，因此你需要设置重点。

According to the geological condition and geometrical characteristics and physical mechanical index of coal seam for large-section face of starting cut of Dafosi coal mine in Binchang mining area,the design of bolt with wire mesh is accomplished and the supporting parameters are given.

根据彬长矿区大佛寺煤矿煤巷大断面开切眼的地质条件、几何特征及煤层的物理力学指标，完成了锚网支护设计，给出了支护参数，利用FLAC软件对煤巷开切眼的稳定性进行了评价。