- 更多网络例句与储能电路相关的网络例句 [注：此内容来源于网络，仅供参考]
-
Aiming at the defects on structure design, electromagnetic design, analysis simulation, optimization design and control technology, double-action iron core mechanism, feedback-hold circuit of energy-saving capacitor voltage and intelligent control circuit were expounded, which can be a guidance for wide application...
针对目前永磁接触器在结构设计、电磁设计、分析仿真、优化设计与控制技术等方面存在的不足，重点阐述了双动铁心永磁机构、储能电容电压的反馈-保持电路及智能控制电路。为促进永磁接触器的推广应用指出了进一步的研究方向。
-
Through studying the mechanism of the electric exploding, an inductive storage circuit with two electric explosive switches is designed to produce shot nanosecond pulse by chopped wave.
论述了电爆炸导体的爆炸机制，设计了两个电爆炸断路开关的电感储能电路，通过斩波来产生一个纳秒级大电流的单触发脉冲。
-
It includes high power high voltage constant-current-charging system, capacitors bank, discharge control system, power supply of preignition for Xe-flashlamps, general control and diagnostic system. The power conditioning system drives flashlamps that pump the SSHCL. Flashlamps are driven by high voltage Silicon Controlled Rectifiers switched, resonant charged, discharge pulse forming network. The system uses microchip and digital circle which is based on CAN-bus for control and diagnostics. Energy diagnosis and thermal management are controlled by computers.
其中大功率高压恒流充电装置采用了L-C串联谐振电路，充电功率大，效率较高；储能装置采用了多节脉冲成形网络，可产生波形良好的强电流放电脉冲；放电控制装置采用高压大功率晶闸管，开关速度快，工作稳定；预燃与触发装置采用了开关电源电路，效率高、功耗小；总控与测量装置采用基于CAN总线的数字电路和单片机技术，控制冷却系统在激光器出光时对脉冲氙灯进行水冷，并对全系统进行控制和状态检测，同时具有过压、过流、过热等保护功能。
-
A novel single-stage power factor correction circuit based on flyback converter is presented in this paper,.A single active switch is used to achieve a fast-regulated-output voltage, the reservoir capacitor voltage is clamped and efficiency is high.
本文提出了一种基于反激变换器的新型单相功率因数校正电路，电路只用一个有源开关就可以获得输出电压的快速调节，储能电容电压被箝位、效率高。
-
In single stage power factor correction converters, the voltage on the storage capacitor is not controlled, its wide voltage range has detrimental effect on the circuit performance.
中文摘要：在单级功率因数校正变换器中，不能控制储能电容电压，而且电压变化很大降低了电路的性能。
-
Meanwhile, the article discusses the methods of magnetizing and demagnetizing the permanent magnet by the pulse of strong current ,which is produced through the discharging of the capacitance in a second order circuit which is made up of RLC in series.
介绍了永磁起重吸盘的工作原理及相对于传统电磁铁的节能、省材、廉价、安全等特点，讨论了应用电容储能经 RL C串联二阶电路放电产生的强电流脉冲对永磁体进行充、退磁的方法及涡流问题，给出了一种控制电路及实验结
-
Then the paper presents a novel-working mode of Boost-Forward single-stage Power Factor Correctors based on the analysis. And get the principle of the conduction mode and the method to control the voltage of the buck capacitor after the analysis of the boundary mode of the PFC converter and the DC-DC converter.
在此基础上，本文首次提出了一种全新的临界工作模式下的单级功率因数校正电路，在对PFC变换器及DC/DC变换器工作在连续及不连续的边界条件进行了讨论后，得出了电路工作状态的精确解并提出了控制储能电容电压的临界点工作方式。
-
The device includes a network with a plurality of switches; a tank circuit connected between the network and a lamp; a controller.
所述装置包括一个包含多个开关的网络；连接在所述网络和灯之间的储能电路；一个控制器。
-
Circulating current through a resonant tank circuit and inverter switches is reduced by feeding high frequency current back through a line inductor.
通过经过一个线路电感线圈将高频电流反馈，可以降低经过一个谐振储能电路和变换器开关的循环电流。
-
And this paper introduced the principium, design ideal and approach of waveform presetting of waveform controlling at will The function of relevant hardware circuit controlling was design in this paper uses litter content RLC surge circuit in simulating the current signal of energy storage welding, and took it as Ug to control the inverter cap energy storage spot welding machine. It realized HFPEC resistance spot welding with hardware circuit and got the effect as good as the system controlled by industrial computer and realized the customization and the low cost of welding machine.
本文所设计的相应硬件控制功能，采用小容量RLC 放电回路来模拟输出储能焊过程的电流波形，由此作为电流给定信号直接控制逆变式电容储能点焊电源，实现了完全由硬件电路构成的高频脉冲电阻点焊，能够获得焊接设备的专用化和低成本化的结果，并且可以得到与工控机控制系统相当的焊接效果。
- 更多网络解释与储能电路相关的网络解释 [注：此内容来源于网络，仅供参考]
-
snubber：缓冲
(1)回能吸收电路[1]:是将缓冲(snubber)电容上的储能返回电源或负载,或称为无损吸收电路. (5)零电流关断(ZCS)和零电流转换(ZCT):是指先将主开关管的电流减小到零,再关断主开关管. 零电流转换(ZCT)是指在主开关管两端并联一谐振电容、谐振电感与辅助开关管串联通路,
-
UI：逆变器
与永磁同步发电机(PMSG)相连的二极管整流器(UR),与二极管整流器(UR)相并联的升压斩波电路,与升压斩波电路相并联的滤波储能电容器C和三相逆变器(UI),与三相逆变器(UI)相连的三相变压器或三相滤波储能电感(TR),
-
rad：弧度
即 i Rdt I Rdt故有效值也称为方均根(rms)值相角 初相位的SI 单位 弧度(rad)常用单位度(DEGREE) 计算中注意必要的转换振幅定义为电容的无功功率 记作 单位乏 (var) 即例 求图示正弦稳态电路中电阻的平均功率 L C 的平均储能
-
tank circuit：储能电路
另外,快速的晶片正在采用螺旋电感(spiral inductor)来构成储能电路(tank circuit). 你也许希望一个可以进行实体建模的工具组,它能协助你建立设计的规则,这样你的器件在布局以后就能体现出应有的性能. Synopsys 的 Borge 说:"我们正在使用一种计算网格.
-
tack line：间索
间索 tack line | 储能电路;屯克电路 tank circuit | 分接[头] tap changer