- 更多网络例句与低电平相关的网络例句 [注：此内容来源于网络，仅供参考]
-
The light source detecter makes used of the variation of the separated voltage by the resistivity of photosensitive resistance input to the singlechip. If the voltage higher than a worth, the singlechip will regard it as high voltage state, it means that the light source has been detected. Otherwise the low voltage state means the light source has not been detected.
光源探测是利用光敏电阻阻值分压的变化向单片机输入，电压大于某值时，单片机认为是高电平，即表示该路探测器感应到光源，否则为低电平，即表示探测器没有感应到光源，如此即可由两路信号判断光源的方向。
-
When either NAND gate pulls low, the SLO state overrides the WHI state from the resistor and the net state is resolved to be logic low.
当与非门的任何一个输入电平为低时，SLO状态通过电阻R1克服WHI状态，使得最后的状态为逻辑低电平。
-
In digital circuitry a circuit, which recognizes a high level to be a logical 1 and a low level as a logical-0 is said to use positive logic .
在数字电路中，每个将高电平识别为逻辑 l。把低电平识别为逻辑0的电路，被称为使用正逻辑。
-
The temperature collected by 18 B20 is detected by single chip computer,according to high and low temperature,single chip computer P2.7-pin output high level or low level to control relay whether there is current in the coil through,according to the coil power relay,normally open contact is closed,no current passing,often a disconnect to maintain contacts so as to achieve the automatic control from the fans stopped.
利用单片机检测18B20采集的温度，根据温度高低，单片机的P2.7脚输出高电平或者低电平，来控制继电器线圈中能否有电流经过，根据继电器线圈通电时，常开触点闭合，没电流经过时，常开触点保持断开，从而实现自动控制电风扇的起停。
-
Bi-level refers to two levels. For sync, this means apulse having two voltage levels (a high and low level, relativelyspeaking), hence the name.
双电平指的就是两个电平，对于同步信号来说，顾名思义，这意味着一个脉冲包含了两个电平值（相对而言，就是一个高电平和一个低电平）。
-
VBB may also rebias AC coupled inputs. When used, decouple VBB: to 0.5 mA. When not used, VBB should be left open.
什么意思？你用的是ecl，应该接GND和－5.2V，高电平大概-0.9，低电平大致-1.8，vbb怎么
-
74LS47N Pinout: The voltage at the TUNDER pin is equal to a logic-low level if the sensor detects a temperature that is less than the factory-programmed threshold temperature.
74LS47N引脚说明：在TUNDER引脚的电压等于逻辑低电平如果传感器检测到的温度是比工厂编程的起点温度低。
-
By the end of the read time slot, the DQ pin will pull back high via the external pullup resistor.
如果要&写1&，则需要把DQ线置为低电平（至少大于1us小于15us），然后设置DQ为高阻态，让外部上拉电阻将DQ拉成高电平，DS18B20会在此后的45~60us之内采样到这个&写1&的高电平
-
The host therefore must stop driving the DQ pin low in order to read its state 15 μs from the start of the read slot.
所以我们如果要&写0&：则需要把DQ线保持低电平至少60us（笔者用了65us），然后将DQ设置为高阻态，让外部上拉电阻将DQ拉成高电平
-
This means clock must be high for 30 - 50 microseconds and low for 30 - 50 microseconds..
这意味着时钟必须是高电平持续30～50毫秒，低电平持续
- 更多网络解释与低电平相关的网络解释 [注：此内容来源于网络，仅供参考]
-
high-level：高电平
因CD唱盘、调谐器、录音座、DVD,都被列为高电平(high level)讯源,虽然面板上有四或五档选择,但你可以随意接,因它们都是高电平讯源,没有实质上的差别. 当然,有高就有低,相对於高电平的就是低电平(low level)讯源,以前风行的LP黑胶唱片系统,
-
LLA LowLevelAccess：低电平接入
LLB LowLevelATMInterface 低级异步传输模式接口 | LLA LowLevelAccess 低电平接入 | LLE LowLevelDriver 低电平驱动器
-
LLL LowLevelLogic：低电平逻辑(电路)
LLC LineLinkConnector 线路链路连接器 | LLL LowLevelLogic 低电平逻辑(电路) | LP ListProcessing 表处理
-
low-level code：低位码
low level | 低电平,低水平,低能级 | low level code | 低位码 | low level debugging | 低级调试
-
low-level radiation：低强度辐射
low-level logic 低电平逻辑 | low-level radiation 低强度辐射 | low-lying level 低能级
-
low imput：低电平输入信号
low gain transistor 低增益晶体管 | low imput 低电平输入信号 | low level 低电平
-
low imput：低电平输入信号Xmj中国学习动力网
low gain transistor 低增益晶体管Xmj中国学习动力网 | low imput 低电平输入信号Xmj中国学习动力网 | low level 低电平Xmj中国学习动力网
-
low level air：大气低层
low level ==> 低电平,低级,低空,低能级,低水平,低水平面 | low level air ==> 大气低层 | low level amplitude limiter ==> 低电平限幅器
-
Lowlight：低照度灯
LOWLEVEL低电平 | LOWLIGHT低照度灯 | LOWLIGHTIND低照度显示电平
-
LLS LowLevelSelector：低电平选择器
LLL LowLevelLogic 低电平逻辑(电路) | LLS LowLevelSelector 低电平选择器 | LLT LowLevelSignalingUnit 低电平信令装置