- 更多网络例句与主轴承相关的网络例句 [注：此内容来源于网络，仅供参考]
-
The defective bearing bushes should be turned out of the bedplate and renewed.
主轴承和连杆轴承应定期检查，损坏的轴瓦应从底座转出并换新。
-
To prevent the loss of oil , place the seals at both ends the crankshaft where it extends through the crankcase .When main bearings are replaced , tighten the bearing cap to the proper tension with a torque wrench and lock them in place with a cotter pin or safety wire after they are in place .
为防止损失的油，放在密封的两头曲轴而延伸，通过曲轴箱，当主轴承更换，收紧轴承盖，以适当的张力与扭力扳手，并锁定他们放在一起特引脚或安全线后，他们都已具备。
-
To validate the FEM calculations of the cylinder block of a six-cylinder in-line diesel engine,the dynamic strain-stress and temperatures of the main bearing wall s and caps were measured on engine testbed with strain-gauge and resistance thermometer.
为评估某直列6缸柴油机缸体有限元强度分析结果，采用应变电测法实测了该发动机缸体上可能的危险部位主轴承座、主轴承盖动态应力以及这些部位的温度。
-
The paper summrized lubrication technology and the selection of lubricant for rotary kiln, grate cooler, mill, conveyor mechanical equipment and large scale fan as following,(1)in rotary kiln, apply oil spoon of circulatory lubrication or pump forced oil supply system in the roller supporting mechanism and use (superscript #)680 high load industrial gear oil, and use lubrication method of idle oil wheel or spray in drive gear wheel and select solid lubricant which has high viscosity, strong adsorbability, good abrasion resistance in utmost pressure and lattic crystal structure,(2) in grate cooler, use immersion oil lubrcation in reducer and boiled oil centralized lubrication method in supporting roller and guide roller bearing, choose (superscript #)1 limit pressure lithium lubrcant grease,(3) in mill, use circulatory lubrication with fluxing oil station in drive mechanism and circulatory lubrication with high-low pressure fluxing oil station in main bearing and sliding shoe bearing and select N320 industrial gear oil.
文章全面总结了回转窑、篦冷机、磨机、输送机械及大型风机的润滑技术和润滑剂的选择。其中，(1)回转窑的托轮支承装置一般采用油勺供油的连续循环润滑方式或油泵强制供油系统，润滑油选用680重负荷工业齿轮油；传动大小齿轮的润滑一般采用带油轮或喷雾的润滑方式，润滑剂宜选用粘度高、吸附性强、极压耐磨性好、具有点阵晶体结构的固体润滑剂；(2)篦冷机中传动减速机的润滑一般采用浸油飞溅润滑；托轮，挡轮轴承的润滑一般采用干油集中润滑的方式，润滑脂一般选用锥入度310~340的1极压锂基润滑脂；(3)磨机中传动装置一般采用稀油润滑站循环润滑和冷却的方式；主轴承或滑履轴承的润滑一般采用高低压稀油润滑站循环润滑和冷却的方式，润滑油一般选用N320工业齿轮油。
-
Engine work, if crude oil filter was a serious blockage of impurities, or due to low temperatures when the oil viscosity changes, the main oil缺油Road will be the engine will lose lubrication, this is very dangerous, especially in the main bearings and connecting rod bearings, if there is no oil will be burned, bearing alloy heat due to friction loss and even journal welded together, eventually forcing the engine to stop working.
发动机工作时，若机油粗滤器被杂质严重淤塞，或者由于气温低而机油粘度变大时，主油道就会缺油，发动机就会失去润滑，这是很危险的，特别是主轴承和连杆轴承，如果没有润滑油会烧坏，轴承合金会因摩擦发热而流失，甚至和轴颈熔焊在一起，最终迫使发动机停止工作。
-
The frequency characteristics of instant- taneous signal of main abnormalities in diesesl engines,including valve sound, piston pin sound,connecting rod bearing sound and sound from the main bearing of crankshaft are analyzed.
从使用角度出发，采用频域分析法，分析了柴油机中气门、活塞销、连杆轴承、曲轴主轴承等部位主要异响的瞬态信号频率特征。
-
The mean value of work loads on a shaft bearing of swivel and rotary table is determined by basic principles of fuzzy theory, considering the loads' fuzziness and the requirement for reliability.
考虑钻机水龙头和转盘主轴承工作载荷的模糊性及可靠性要求，应用模糊数学基本原理求得平均计算载荷，从而计算出主轴承的模糊可靠性寿命。
-
The variable load operating mode of the rotary table and swivel was transformed equivalently into stable load operating mode, and the equations for calculating the equivalent weig...
即将转盘和水龙头主轴承由变载荷工况向稳定载荷工况作等效转换，从而导出等效当量动载荷Pm 的计算式及主轴承寿命估算公式，并以 40 0 0m深井钻机水龙头主轴承为例，进行了疲劳寿命的估算
-
The currency-used equations for calculating the life of the main bearings on rotary table and swivel take no consideration of all the affecting elements. The author offers thereby new equations that take an overall consideration of the load, rotary speed, lubrication, assembling, working environment, material and surface hadness.
针对现有文献给出的转盘和水龙头主轴承寿命估算公式对多种影响因素考虑不充分，与实际工况有一定出入的问题，推导出全面考虑载荷、速度、润滑、装配、工作环境和材料及表面硬度等多种影响因素，估算转盘和水龙头主轴承寿命的新公式。
-
A rotary two-stroke engine including a multi-cylinder block rotatably mounted on two main bearings within an engine housing, a crankshaft journalled for rotation within said main bearings, indirectly geared at a ratio of 2:1 to said cylinder block and piston members connected to said crankshaft which induce gas through ports in said cylinders via side entry tracts in said engine housing, being sealed by rotating seal rings.
一种旋转二冲程发动机，包括一个多缸机体、一个曲轴和活塞组件，其中该多缸机体可旋转地安装在发动机机体中的两个主轴承之中，曲轴支承在所说主轴承中旋转，并以2∶1的传动比间接地与所说汽缸体啮合，而活塞组件与所说曲轴连接，活塞从所说汽缸中的气口处经所说发动机上的所说进气通道将燃气吸入，该通道被旋转的密封环密封。
- 更多网络解释与主轴承相关的网络解释 [注：此内容来源于网络，仅供参考]
-
main brasses：主轴承轴瓦
main branch road 主要支路 | main brasses 主轴承轴瓦 | main breaker 主开关
-
main bearing：主轴承
主轴承(Main Bearing) 引擎内支撑曲轴的轴承. 歧管压力(Manifold Pressure) 涡轮增压器运作时位于进气歧管内的压力. 排气量(Displacemint)在引擎的某一循环运作中,能将全部空气及混合气送入所有汽缸的能力,
-
main bearing babbitting jig：主轴承
main beam 主横梁 | main bearing babbitting jig 主轴承 | main bearing babbitting jig 主轴承浇铸巴氏合金夹具
-
main bearing babbitting jig：主轴承浇铸巴氏合金夹具
main bearing babbitting jig 主轴承 | main bearing babbitting jig 主轴承浇铸巴氏合金夹具 | main bearing bush 主轴承衬
-
main bearing babbitting jig：主轴承浇巴氏合金夹具
main bearing ==> 主轴承 | main bearing babbitting jig ==> 主轴承浇巴氏合金夹具 | main bearing boring bar ==> 主轴承镗杆
-
main bearing blots of diesel engine：主轴承螺栓
柴油机工作过程:Working Process of Diesel Engine | 主轴承螺栓:main bearing blots of diesel engine | 船舶柴油发电机:Marine Diesel Engine Generator
-
main bearing boring bar：主轴承镗杆
main bearing babbitting jig ==> 主轴承浇巴氏合金夹具 | main bearing boring bar ==> 主轴承镗杆 | main bearing boring tool ==> 主轴承镗刀
-
main bearing reboring device：主轴承精镗削工具
main bearing reamer ==> 主轴承铰刀 | main bearing reboring device ==> 主轴承精镗削工具 | main bearing removal ==> 主轴承拆卸
-
Le palier de vilebrequin：曲轴油承(主轴承)
Le canal de graissage 曲轴油孔(曲轴阀滑油道) | Le palier de vilebrequin 曲轴油承(主轴承) | Le palier d'arbre a cames 凸轮轴轴承
-
main step bearing：主支承轴承
main stem ==> 主茎,主要街道 | main step bearing ==> 主支承轴承 | main steps ==> 主轴承瓦,主轴承轴瓦