pitch diameter of thread

pitch diameter of thread的基本解释

-

螺纹中径

与pitch diameter of thread相关的网络例句 [注：此内容来源于网络，仅供参考]

In order to real-timely and accurately measure thread parameters such as thread angle(tooth-type half-angle),screw-pitch,lead,thread height,major diameter,minor diameter,pitch diameter,helix angle etc,and enhance the measuring accuracy,a non-contact thread parameter measuring system based on an array CCD was designed and achieved.

为实时准确地对螺纹的牙型角、螺距、导程、螺纹高度、大径、小径、中径、螺纹升角等参数进行测量，并提高测量精度，设计并实现了基于面阵CCD的螺纹参数非接触测量系统。

Roundness tolerance of pitch diameter Roundness tolerance for a minimum of 345o circumferential arc of the pitch diameter shall not exceed .002 inch (0.051 mm) total, or one half the pitch diameter tolerance if the pitch diameter tolerance is less than .004 inch (0.102 mm); roundness tolerance of the remaining 15o maximum circumferential arc shall not exceed .004 inch (0.102) total, provided such tolerance does not result in excrescence on the thread flank.

圆度公差沥青直径圆容忍最低限度的345o圆周弧音高直径不得超过0.002英寸（ 0.051毫米）总，或一的一半，足球场直径公差，如果沥青直径公差小于0.004英寸（ 0.102毫米）；圆的耐受性，其余15o最大周弧不得超过0.004英寸（ 0.102 ），共计提供这样的宽容不会导致在excrescence对线程的侧翼。

Tooth Proportions.—There are 17 pitches: 2.5/5, 3/6, 4/8, 5/10, 6/12, 8/16, 10/20, 12/24, 16/32, 20/40, 24/48, 32/64, 40/80, 48/96, 64/128, 80/160, and 128/256. The numerator in this fractional designation is known as the diametral pitch and controls the pitch diameter; the denominator, which is always double the numerator, is known as the stub pitch and controls the tooth depth. For convenience in calculation, only the numerator is used in the formulas given and is designated as P. Diametral pitch, as in gears, means the number of teeth per inch of pitch diameter.

齿比——一共有17种齿比：2.5/5，3/6，4/8，5/10，6/12，8/16，10/20，12/24，16/32，20/40，24/48，32/64，40/80，48/96，64/128，80/160和128/256在这一系列的分数中的分子是径节，径节的大小决定了节圆的直径；而分数中的分母通常是分子的两倍，分母是残余径节，它的作用是控制齿槽的深度为了方便计算，在所有的公式中都使用分子作为计算参数，并且与齿轮的表示方式一样定义为径节P尺寸，也就是在节圆上，每英寸长度上的齿数

与pitch diameter of thread相关的网络解释 [注：此内容来源于网络，仅供参考]

frontomental diameter：额颏径:额至颏的距离

extracanthic diameter 外眦径:两眼上睑与下睑外侧结合点之间的距离 | frontomental diameter 额颏径:额至颏的距离 | fronto-occipital diameter 额枕径:同occipitofrontal diameter

pitch cone：节圆锥

节圆直径 pitch diameter | 节圆锥 pitch cone | 节圆锥角 pitch cone angle

P.C. Pitch Circle：节圆

P-Y-R Pitch-Yaw-Roll 纵倾,横倾,横摆 | P.C. Pitch Circle 节圆 | P.D. Pitch Diameter 节圆直径