flange bushing

与flange bushing相关的网络例句 [注：此内容来源于网络，仅供参考]

The disc type counter current chromatographic separation column comprises at least a or a plurality of discs provided with designing slots, clapboards at two sides of each disc, the cylinder rotating axis, an upper flange and a lower flange; the cylinder rotating axis is hollow and passes through the center of the upper flange, the lower flange, the discs and the clapboards; the inner edge and the outer edge of the upper flange, the lower flange, the discs and the clapboards are provided with a plurality of bolt pieces that fix the upper flange, the lower flange, the discs and the clapboards together.

一种多功能高效逆流色谱仪，它由盘式逆流色谱分离柱、配重体、行星架、柱体自转轴、行星轮、中心轮、中心公转轴、电机、传动装置、速度控制装置和保温机箱组成；所述的盘式逆流色谱分离柱，它包括有至少一个或多个设槽的圆盘、每个圆盘两侧的隔板、柱体自转轴和上法兰、下法兰；所述的柱体自转轴为空心，贯穿在上法兰、下法兰、圆盘及隔板的中心；在上法兰、下法兰、圆盘及隔板的内外边缘设有多个螺栓部件，将上、下法兰、圆盘及隔板固定在一起。

Results indicate that radial distance of the bushing from the rotor center and the radius of the hemispherical bushing significantly affect wear rate,and minimzing both two values will result in lowest wear for micro-rotor systems in MEMS.However,it is noted that the bearing radius sets a lower limit on the hemispherical bushing radius since the bushings are located beyond the rotor inner radius.It is desirable to reduce their effects on friction and wear on micro-rotors by regulating the radius of the bushing and the radial distance of the bushing from the rotor center within permissive range of micro-fabrication.Severe wear exists with increasing applied load and rotating speed of the rotor.Stress distributions in the contact region are different from Hertz solutions due to the convergence stresses apearing on the uncontinuous curvature line and the contact pressures display symmetrical parabola in the contact region.

结果表明：在MEMS微转子系统中，微转子轴衬偏心距离和转子轴衬半径影响线磨损率，以两者减至最小为较理想，但须注意设计中轴承半径的限制，并使轴衬偏心距离大于轴承内半径；在转子加工制造许可的范围内，可以通过调整转子轴衬的半径和偏心距离来减少摩擦磨损对微电机的影响，随着转子所承受载荷和转子旋转速度的增加，其磨损严重；接触区的应力分布不同于经典Hertz解，这是由于应力集中出现在不连续的曲率线上，且接触区的接触压力呈现轴对称抛物线状分布。

It's equipped with anti-liquid overflow breather valve, anti-aging overhead nitrogen charging valve, thermometer, volumeter and asphalt testing valve and reserves feed opening interface flange, high level and high high level alarm flange, blender reserved hole flange and discharge opening flange used to output asphalt.

配备防冒液呼吸阀、防老化顶置充氮阀、温度表、容量计、沥青检测阀，并预留进料口接口法兰、高位及高高位报警接口法兰、搅拌器预留孔法兰和输出沥青的卸料口法兰。

与flange bushing相关的网络解释 [注：此内容来源于网络，仅供参考]

flange bushing：凸缘衬套

flange body 凸缘体 | flange bushing 凸缘衬套 | flange chuck 法兰卡盘