顺序控制

With the use of a robust error mapping function, an affine model-based target tracking algorithm is formulated, in which a quasi-Newton's iterative method is implemented in the optimization progress.

算法中使用的"由粗至精"计算策略以图像金字塔数据结构为基础，采用自顶向下的计算顺序，并在每层金字塔上结合对鲁棒性误差映射函数中控制参数所做的逐步降级处理，实现了逐步求精的计算目的。

The device produces trigger signals by controlling system then acts on valve banks, make them following the given frequency and order breakover, in the mode of spray wave to realize electromotor maximum starting torque and complete safe starting.

该装置通过控制系统产生触发信号，作用于晶闸管阀组，使其按照设定频率及顺序导通，以跳波方式实现电动机转矩最大化，使电动机完成安全起动全过程。

The algorithm GS to solve the problem of inverse dynamics based on the optimal theory is proposed, by using the numerical methods of Gill and shooting target, the optimal joint driven torques are obtained With the smooth joint trajectory motion, a fast and stable inverse dynamics method is proposed, it provides a new effective way to control the flexible manipulator The trajectory planning in the joint space and Cartesian coordinates is especially discussed In terms of kinematics of space flexible link manipulators, a sequential integration method for inverse dynamic analysis of flexible manipulators is developed The concrete results of simulations tested and verified the validity of proposed methods, and some valuable conclusions are achieved.

提出了求解基于最优理论的柔性臂逆动力学问题的GS法(Gill—Shooting method)，得到了柔性臂关节的最优驱动力矩；提出了基于光滑关节运动轨迹的柔性臂逆动力学的快速稳定方法，为柔性臂控制提供了一条新的途径；探讨了关节空间和直角坐标空间柔性臂的轨迹规划问题；研究并完善了结合柔性臂运动学的顺序积分的逆动力学方法。通过具体实例的仿真研究，验证了所提出的柔性臂逆动力学方法的有效性，得出了一些很有价值的结论。

We use MCU to control the filling material sequence and quantity number of system.Meanwhile ,we also control the opening and closing in turn between big furnace and small one by MCU.The result can be displayed on the control desk by digital display tube.

用单片机控制系统上料的顺序、上料的批次、实现大小钟之间的交替打开、关闭，并将结果通过数码管显示到操作台；料车的行进状态及检测、显示则有S7-200可编程控制器和西门子TD200文本显示器共同完成。

"Timer",A timer can be used to control the sequence of process.

"，"计时器用来控制过程的顺序。

For this application, asynchronous triggering is used to control the following sequence of events

对于这种应用，采用同步触发来控制以下的时间顺序

To control production sequence and make appropriate adjustment, so as to realize balanced production

对产品生产顺序进行控制和灵活调整，实现均衡化生产

The control mainly process decides the sequence of the chosen rules.

控制主要的过程中决定的顺序选择的规则。

Next,determine the sequence in which control operations are to occur and the relative timing of the operations.

接着，确定待发生控制事件的顺序及操作的相对时序。

This paper describes the technical features, process principle and process flow of that technique, putting emphasis on the implementation procedure of hole position arrangement, measuring control, boring and hole completion, grouting sequence, pressure treatment and hole seal. It discusses key points of construction quality control, analyzes problems occurred during the construction and puts forward treatment measures.

文章介绍了袖阀管法注浆技术特点、工艺原理及工艺流程，重点从孔位布置、测量控制、开孔与成孔、注浆顺序和压力、封孔处理等方面介绍了袖阀管法注浆实施过程，论述了质量控制要点，对施工过程中出现的问题进行了分析，并提出了处理措施。

Chrysanthemum of 10 thousand birthday is lax to edaphic requirement, with the arenaceous qualitative loam with fecund, good drainage had better.

万寿菊对土壤要求不严，以肥沃。排水良好的砂质壤土为好。

He unstepped the mast and furled the sail and tied it.

他拔下桅杆，把帆卷起，系住。