镀层

1 Laid on the observation points, the next gate in the first paragraph and the chamber are in side-dock-type pier and construction of a wide bottom seam laid 8 to each end of the settlement within 24 observation points nails; chamber 14 Fu wall segments are in lock wall at both ends of the floor laid four nails into account the settlement of 56 observation points; settlement nail making use of 40cmФ18 rebar welded copper top round hat hemisphere processed, buried, when coupled with oblique bars welded to the end of plate surface layer and vertical reinforcement, the top highlight the concrete surface, about 1.5 ~ 2.0cm in order to guarantee points are solid.

3.2.1观测点的布设上、下闸首及闸室坞式段均在边墩底板及施工宽缝的两端各布设8个沉降钉计24个观测点；闸室14节扶壁段均在闸墙底板两端各布设4个沉降钉计56个观测点；沉降钉的制作采用40cmФ18螺纹钢顶端焊接镀铜半球圆帽加工而成，埋设时配以斜筋焊接在底板面层及竖向钢筋上，顶端突出砼表面1.5～2.0cm左右，以保证点位稳固。

Sulphates, nitrates and phosphates are generally considered to be protective towards galvanizing.

硫酸盐、硝酸盐和磷酸盐一般被认为对镀锌层有保护作用。

The residual silicon oxide on the silicon surface is thought to inhibit silicides formation of W and Mo.

然而如果在矽和钼或钨之间垫一层钴，则在相同的蒸镀与退火条件，矽化物就很容易形成。

Made of metal or a composite base, diamond stone sharpeners have an outer layer of micron-sized diamonds bonded to a metal surface.

由金属或合成材料制造，钻石磨刀器在金属表面上镀有一层微米尺寸级的钻石涂层。

In order to obtain reasonable processing parameter of electroless nickel plating, the influences of the concentration of reductants NaH_2PO_2 and complex agents DL-lactic acid, stabilizers ,pH value and temperature on the deposition rate , the content of P and stability of the plating solution were studied.

在化学镀镍的工艺中，研究了次亚磷酸钠和络合剂乳酸的浓度、pH值、稳定剂和温度等工艺参数等对沉积速度和镀镍层含磷量的影响，找出了合理的化学镀镍工艺：还原剂的浓度为25 g/l~ 30g/l，络合剂乳酸的浓度为8ml/l ~ 12 ml/l，pH值的范围为4.6 ~ 4.9，选择作稳定剂，温度为85℃左右。

By analyzing and comparing the above test results, the special demands for welding current and time and pressure in the spot welding of zinc-coated steels were put forward.

而在这些产品的装配和制造中，往往会用到电阻点焊方法，由于镀锌钢板表面锌层的熔点很低、硬度也低，给点焊带来一定的困难［1］。

By analyzing and comparing the above test results, the special demands for welding current and time and pressure in the spot welding of zinc-coated steels were put forward.

为了在需点焊加工的产品上推广使用镀锌钢板，并保证其焊接质量，本文对普通冷轧钢板、电镀锌钢板和两种不同锌层厚度的热镀锌钢板进行了一系列点焊工艺及力学性能试验，并通过对试验结果的数据处理和理论分析，找出了几种材料点焊工艺性能上的差异，得出了一套合适的点焊焊接规范范围。

Face on the first glass prism element. The interference filter is formed by depositingtwo prism elements are joined together.

这个滤光片是在两个棱镜连接前由第二棱镜一面镀SiO2/TiO2复合层膜构成。

The relevant spot welding parameters for every kind of zinc-coated steels were proposed.

为了在需点焊加工的产品上推广使用镀锌钢板，并保证其焊接质量，本文对普通冷轧钢板、电镀锌钢板和两种不同锌层厚度的热镀锌钢板进行了一系列点焊工艺及力学性能试验，并通过对试验结果的数据处理和理论分析，找出了几种材料点焊工艺性能上的差异，得出了一套合适的点焊焊接规范范围。

Keywords zinc coating;zinc-coated sheet steel;formability;adhesion

锌层； 镀锌钢板；成形性能；附着特性

Chrysanthemum of 10 thousand birthday is lax to edaphic requirement, with the arenaceous qualitative loam with fecund, good drainage had better.

万寿菊对土壤要求不严，以肥沃。排水良好的砂质壤土为好。

He unstepped the mast and furled the sail and tied it.

他拔下桅杆，把帆卷起，系住。