钻头

So Benoto Method, reverse circulation drilling with quadruple-wing drag bits, drilling with roller-type cutting head and combined drilling technology was adopted as well as wall protection with mud, which is strictly districted in Hongkong and Macao.

根据工程的具体情况，采用贝诺特工法、反循环四翼刮刀钻头钻进、滚刀钻头钻进等组合钻进工艺，同时采用在港澳地区限制严格的泥浆护壁钻进。

On the base of electroplated Ni-Co alloy diamond bit, Ni-Fe alloy matrix by electroplating was studied in this paper.

本论文在电镀镍-钴合金钻头的基础上，对镍-铁合金胎体钻头进行了试验与研究。

Electroplated diamond bits are important tools of exploration and construction. Performances of bits are basis on their procedure of manufacture.

电镀金刚石钻头是各类勘查施工中的重要工具，钻头的性能取决于它的生产工艺。

Auger bit, square shank drill bit, electrical, hammer drill bit, masonry drill bit, flat wood bit, forstner drill lok, chisel.

8A79 8A81 自螺钻、万孔钻、冲击钻头、电锤钻头、木工扁钻、木工绞孔钻、门锁套装开孔器、调节圆孔钻、凿子。

When the guide hole drilling is completed, unloaded oriented bit, to accommodate tube launchers and connect with reverse bore bit and rotary joint, Then after the rotary joint drill pipe connected to Rafah, to Reamer drilling.

当导向孔钻进完成后，卸下导向钻头、发射器容纳管，接上反向扩孔钻头和旋转接头，然后在旋转接头后接上回拉钻杆，进行回拉扩孔钻进。

Supply contact group, were positive,, mountain hafnium, butt Qi, Wang main parts such as automatic lathes, table lathes have, belts, steam-driven chuck Block, Grinding, open closed claw, Tool,òsmall motors, clutches, cam blanks, chuck, drilling chuck, cam, cam Events, cam thimble, tools, wheel discs, retaining materials arm, S plate, rolling round silk flower attack, attack left tooth wire, drill bits, L-drill, round bars, tungsten steel round bars, die, plate braces, dental regulation, cone, non-ditch attack silk, silk YAMAWA attack Japan, Japan OSG silk attack.

供应洽群、名阳、昌勇、山铪、錡夆、王主等自动车床零配件，有桌上车床、皮带、汽动夹头座、磨刀机、开闭爪、车刀、打油小马达，离合器、凸轮毛胚、夹头、钻尾夹头、凸轮、活动凸轮、凸轮顶针、车刀、砂轮碟，挡料臂、S型板、滚花轮丝攻，左牙丝攻、钻头、左旋钻头、圆棒，钨钢圆棒、板牙、板牙套、牙规、牙轮、无沟丝攻、日本YAMAWA丝攻、日本OSG丝攻。

In the commonly used positive cycle of drilling, the mud pump is to rinse the surface with water medium ─﹑ mud or polymer washing fluid at a certain pressure, through the high-pressure hose taps and drill column ﹑ center hole in the bottom of the direct-drill in order to achieve Cooling ﹑ be cutting down the drill cuttings removal and transport to the surface purpose.

在常用的正循环钻探中﹐泥浆泵是将地表冲洗介质─清水﹑泥浆或聚合物冲洗液在一定的压力下﹐经过高压软管﹑水龙头及钻杆柱中心孔直送钻头的底端﹐以达到冷却钻头﹑将切削下来的岩屑清除并输送到地表的目的。

A APDL program is developed for analyzing the contact stress of journal bearing pair of roller cone bit. The 25 contact stress cases of different clearance fit(including clearance of large bearing is bigger, equal to and smaller than that of small bearing) journal bearing pair of the 8 1/2XXX roller cone bit are analyzed. The result is that the maximum contact stress is less when the clearance of large journal bearing pair is smaller than or equal to that of small journal bearing pair.

用参数化设计语言APDL编制了牙轮钻头滑动轴承的ANSYS接触有限元分析程序，根据钻头制造厂方提供的某8 1/2的轴承配合间隙尺寸，分三种不同的间隙配合（大轴间隙大于小轴间隙、大轴间隙等于小轴间隙、大轴间隙小于小轴间隙），共25种情况，对轴承的表面的接触应力进行了分析，得出：大轴间隙小于等于小轴间隙时最大应力比较小。

Cone bit ; bit bearing ; stress analysis ; finite element analysis

牙轮钻头；钻头轴承；应力分析；有限元法

The bit has a cone rotatably mounted to a bearing pin of the bit body.

钻头具有可旋转地安装至钻头体牙轮轴(19)的锥体(29)。

Chrysanthemum of 10 thousand birthday is lax to edaphic requirement, with the arenaceous qualitative loam with fecund, good drainage had better.

万寿菊对土壤要求不严，以肥沃。排水良好的砂质壤土为好。

He unstepped the mast and furled the sail and tied it.

他拔下桅杆，把帆卷起，系住。