钳

In order to study the movement characteristic of nipper mechanism on comber,the simulation model based on assur group was built up according to constituents of nipper mechanism.

文中以精梳机钳板机构为研究对象，根据机构的组成，采用杆组仿真模块构建了精梳机钳板机构仿真模型；并利用Simulink仿真软件包对钳板机构的运动规律进行隐式求解，得到各构件的运动特性曲线。

This paper analyzes the moving characteristics of nipper mechanism of new type FA266 comber made in China, and discusses the eccentric shaft and eccentricity influence on combing processing and the moving of nipper mechanism, which provides the theory basis of the from of opening-closing time adjusting mechanism, dimension, process parameter, and adjustment pattern.

分析了国产新型精梳机FA266钳板机构的运动规律，讨论了偏心轴偏心距对精梳工艺及钳板机构运动的影响，为确定国产新型精梳机中钳板运动的开闭口定时调节机构的形式、尺寸、工艺参数及调节方式提供理论依据。

This paper analyzes the moving characteristics of nipper mechanism of new type FA266 comber made in China, and discusses the eccentric shaft and eccentricity influence on combing process ing and the moving of nipper mechanism, which provides the theory basis of the from of opening-closing time adjusting mechanism, dimension, process parameter, and adjustment pattern.

分析了国产新型精梳机FA266钳板机构的运动规律，讨论了偏心轴偏心距对精梳工艺及钳板机构运动的影响，为确定国产新型精梳机中钳板运动的开闭口定时调节机构的形式、尺寸、工艺参数及调节方式提供理论依据。

We have established optical tweezers and manipulation systems, and analyzed the optical spring constant by detecting Brownian motion or optical forced oscillation of the trapped particle.

我们成功建立了光钳微操控系统，并利用钳住微粒时因为热扰动所造成的布朗运动或是利用光学震荡力所造成的微力震动强度及相差定义光钳光学弹力常数。

Correct, the demolition of the gas valve is the gas valve from the spare machine work location, the body upperend in the jaws of a pair of pliers-bed of one side, the seat of the valve body with M8X 25 hexalobular heicobacter of hexalobular head alignment valve set's center position, hupensis the other side of the top in the jaw, to increase the contact area on the screw to prevent bursting valve set, at the same time makes it easy to remove.

气阀正确的，拆卸方法是，把气阀从机器工作位置拆下来，将阀体的一头放在钳台的钳口一边，阀体的阀座边用M8X 25内六角螺杆的内六角头对准阀套的中间位置，螺的另一边顶在钳口上，目的是增加螺杆的接触面积，防止顶破阀套，同时便于取出卡簧。

Correct, the demolition of the gas valve is the gas valve from the spare machine work location, the body upperend in the jaws of a pair of pliers-bed of one side, the seat of the valve body with M8X25 hexalobular rationl hexalobular head alignment of valve set's center position, hupensis the other side of the top in the jaw, to increase the contact area on the screw to prevent bursting valve set, at the same time makes it easy to remove.

气阀正确的，拆卸方法是，把气阀从机器工作位置拆下来，将阀体的一头放在钳台的钳口一边，阀体的阀座边用M8X25内六角螺杆的内六角头对准阀套的中间位置，螺的另一边顶在钳口上，目的是增加螺杆的接触面积，防止顶破阀套，同时便于取出卡簧。

The "photon gate" formed by pulse superimposed on DC level is equivalently performed by monostable circuit in pulse generator.

一种命名为电压钳控制的电流钳技术被应用来改进传统的膜片钳放大器。

Finally, analysis and discussion in dynamic stability of nipper mechanism show that instable regions become wider with speed increasing and the chief factor determining motion stability of nipper mechanism is its first two modes which can be changed by adjusting the ratio of the length and inertia.

最后利用该参数平面分析了钳板机构的稳定性，分析表明，随着速度的提高，不稳定区域越来越宽；影响钳板机构稳定性的主要原因是机构的前两阶模态，可以通过调整构件的长度比、惯性矩比来提高钳板机构运动稳定性。

The paper elucidates the low of opening-closing of nipper, the timing of cylinder's combing, the timing of detaching-lapping and the changing law of nip pressure, as calculated and analyzed by computer, in different detaching distance on E716 comber.

运用计算机计算并分析了E7/6型精梳机在不同落棉刻度时钳板的开启闭合规律、锡林梳理定时、分离接合时间及钳板钳口压力的变化规律。

The breakout tong is placed on the top tool joint and the makeup tong is placed on the bottom tool joint.

钻工在钻杆或管子接头上上打上大钳（内钳打在上方接头上，外钳打在下方接头上）。

Since historical times,England ,where the early inhabitants were Celts, has been conquered three times .

从有历史以来，英国，在此地早期居住的是凯尔特人，已经被征服了三次。

Bluetooth OBEX File Transfer Enables the sending and receiving of files on your phone via Bluetooth.

蓝牙OBEX文件移动允许经过蓝牙传送和接受文件。。。。