返回的

The orthograph can be transformed to the 3D graphics by using 3D functions in AutoCAD, thus all analysis and reasoning for the solution can be clearly visualized in 3D space, and then by baking to the 2D environment the solution can be easily made.

借助AutoCAD的三维图形功能，可将平面正投影图转化为空间三维图形，在三维空间进行分析、推理和求解，然后再返回二维作图，使解题过程概念清晰，可视性强。

One of your counterparts managed to get himself outed back on Ragnar Station.

你们的一个同伴还成功返回大本营

DESCRIPTION /2--WAISTBAND RELAXED /3---POINT TO MEASURE "K" FROM WAISTBAND TOP EDGE /4---HIP WIDTH /5--FRONT RISE FROM WAISTBAND TOP EDGE /6---BACK RISE FROM WAISTBAND TOP EDGE /7---TIGHT AT CROTCH 2,5CM BELOW RISE /8----SIDE LENGTH FROM WAISTBAND TOP EDGE- OUTSEAM /9----INSEAM /10----LEG OPENING /11-----BOTTOM HEM HEIGHT /12---WAISTBAND HEIGHT /12-----IPPER LENGTH / 133LOOP HEIGHT /14----LOOP WIDTH /15 ----POCKET WIDTH AT TOP / 16---POCKET HEIGHT /17---POCKET WIDTH AT TOP /18---POCKET HEIGHT AT CENTER /19---FLAP LENGTH AT CENTER /20---FLAP LENGTH AT CENTER /21---LEFT CARGO POCKET WIDTH /22---LEFT CARGO POCKET HEIGHT, AT CENTER /23----RIGHT CARGO POCKET WIDTH /--RIGHT CARGO POCKET HEIGHT, AT CENTER

-说明/ 2 -腰带松动/ 3 ---点测量的& K &从腰带顶部边缘/ 4 ---髋宽/ 5 -前台上升腰带顶部边缘/ 6 ---返回上升腰带顶部边缘/ 7 ---致密在裆2，5中医以下上升/ 8 ----侧长度从腰带顶部边缘， OUTSEAM / 9 ---- INSEAM / 10 ----专家组开幕/ 11 ----底阁下身高/ 12 ---腰带身高/ 12-----IPPER长度/ 133LOOP身高/ 14----LOOP宽/ 15 ----POCKET宽顶端/ 16---POCKET身高/ 17---POCKET宽顶端/ 18---POCKET高度中心/ 19 ---皮瓣长度中心/ 20 ---皮瓣长度中心/ 21 -左货物口袋宽/ 22 ---左货物口袋身高，中锋/ 23----RIGHT货物口袋宽/-右键货物口袋身高，中锋机器反译，不知道有没有用

DESCRIPTION /2--WAISTBAND RELAXED /3---POINT TO MEASURE "K" FROM WAISTBAND TOP EDGE /4---HIP WIDTH /5--FRONT RISE FROM WAISTBAND TOP EDGE /6---BACK RISE FROM WAISTBAND TOP EDGE /7---TIGHT AT CROTCH 2,5CM BELOW RISE /8----SIDE LENGTH FROM WAISTBAND TOP EDGE- OUTSEAM /9----INSEAM /10----LEG OPENING /11-----BOTTOM HEM HEIGHT /12---WAISTBAND HEIGHT /12-----IPPER LENGTH / 133LOOP HEIGHT /14----LOOP WIDTH /15 ----POCKET WIDTH AT TOP / 16---POCKET HEIGHT /17---POCKET WIDTH AT TOP /18---POCKET HEIGHT AT CENTER /19---FLAP LENGTH AT CENTER /20---FLAP LENGTH AT CENTER /21---LEFT CARGO POCKET WIDTH /22---LEFT CARGO POCKET HEIGHT, AT CENTER /23----RIGHT CARGO POCKET WIDTH /--RIGHT CARGO POCKET HEIGHT, AT CENTER

-说明/ 2 -腰带松动/ 3 ---点测量的& K &从腰带顶部边缘/ 4 ---髋宽/ 5 -前台上升腰带顶部边缘/ 6 ---返回上升腰带顶部边缘/ 7 ---致密在裆2，5中医以下上升/ 8 ----侧长度从腰带顶部边缘， OUTSEAM / 9 ---- INSEAM / 10 ----专家组开幕/ 11 ----底阁下身高/ 12 ---腰带身高/ 12-----IPPER长度/ 133LOOP身高/ 14----LOOP宽/ 15 ----POCKET宽顶端/ 16---POCKET身高/ 17---POCKET宽顶端/ 18---POCKET高度中心/ 19 ---皮瓣长度中心/ 20 ---皮瓣长度中心/ 21 -左货物口袋宽/ 22 ---左货物口袋身高，中锋/ 23----RIGHT货物口袋宽/-右键货物口袋身高，中锋

Pasang returned with Sonam and made the second ascent.

1958年 pasang返回索南和作出的第二次上升。

In June 2008, Rika returned to the modeling world, according to the Pinky Profile listed below.

在2008年6月， rika返回到建模世界，根据该pinky的个人资料列在了下面。

There was no commotion in the terminal when he drove away to his home in Piscataway, he said.

在他开车返回皮斯卡塔韦（美国新泽西州东北部的一个镇区）时，机场客运站还一切正常。

Unlike most other submachine guns, the return spring was located in the buttstock and was linked to bolt via long push-rod, pivotally attached to the rear of the bolt.

与大多数其他冲锋枪，返回春天位于枪托，并通过与螺栓长推杆，pivotally附在后面的螺栓。

Officers in Bristol, Canterbury and Long Lartin returned to work in the afternoon, but other POA members said ...

人员在布里斯托尔，坎特伯雷和长期lartin返回工作在下午的，但其他校议员说。。。

To predesign conversion way of unchanged ofdata bit to be zero, and initial transmission applies conversion way of zero modulation to send data b.

判断是否需要重传，如果不需要，则返回步骤a发送新数据；否则，判断预先选定的变换方式是否已全部用过，如果不是，则依序选择下一变换方式，如果是，则从变换方式0开始重新依序选择；c。

Since historical times,England ,where the early inhabitants were Celts, has been conquered three times .

从有历史以来，英国，在此地早期居住的是凯尔特人，已经被征服了三次。

Bluetooth OBEX File Transfer Enables the sending and receiving of files on your phone via Bluetooth.

蓝牙OBEX文件移动允许经过蓝牙传送和接受文件。。。。