轴向间隙

The result is meaningful to the improvement of the design of the four-fulcrum thrust ball bearing pack of turbodrill.

研究结果对轴承组的设计改进和涡轮钻具轴向间隙的调整有一定指导意义。

The experimental results show that the eddy current sensor has high sensitivity and preferable static and dynamic performances.

试验结果表明，电涡流位移传感器静态和动态性能好、灵敏度高、输出信号强，能满足涡旋压缩机轴向间隙小位移量的测量要求，输出波形信号频率能精确反映压缩机的转速变化情况。

One of two magnetic rings is fixed and the other can move axially.Because of the function of magnetic field,two magnetic rings keep each other with a due distance axially.

在磁场作用下，两环自动保持一定的轴向间隙，任何外力作用下此间隙的改变会产生一个恢复力，即弹力。

Planet reduction shown in figure 6. Loose nut 6 "nut + washer + anti-loose nut". The explored view is Adjust torque 350~400N.m, rotate hub 13 at the same time. 5 and a radial force F=70N crease, hub can rotate free. Then fix lock washer into nut 6, fasten loose nut with torque 400N.m and make spacer control 0.05~0.15mm.

调整时，用 350~400N.m 力矩旋紧螺母 6，同时转动轮毂 13，使两轴承处于正确位置，然后，稍旋松螺母 6，在轮辋螺栓处施加一个切向力 F=55N.m，此时轮毂应能自由转动，然后装上止动垫片 5，将其卡爪折入螺母 6 的防转槽内，再用 400N.m 的力矩旋紧防松螺母，使轴向间隙控制在 0.05～0.15mm 之间。

Thirdly, mathematic model of flowing fluid will be established in both radial gap and axial gap, and the pressure distribution laws will also be concluded in these two gaps.Fourthly, pressure distribution drawing will be made in entrance and cover board of pumps and axial gap of balance device.

为了分析新型轴向力平衡装置间隙的内部流动，建立了径向间隙和轴向间隙内部的流动数学模型，并应用粘性不可压缩流体的纳维—斯托克斯方程和流体的连续性方程，推导出了两间隙进出口压力差和泄漏量的关系式，进而得出平衡装置间隙内部的压力分布规律。

Disk rotation balance week, will go to a certain point of view, the local emergence of the greatest axial clearance or minimum clearance space.

平衡盘转动一周，会在转到某一角度时，局部出现轴向间隙的最大间隙或最小间隙。

At this point, if the sizes of solid particles with the liquid into balance disc constantly in front of the high-pressure area, particle size less than or equal to A as the solid particles will flow through the axial gap.

此时，若大小不一的固体颗粒随着液体不断涌向平衡盘前面的高压区，粒径小于或等于A的固体颗粒会随着液流通过轴向间隙。

To the problems of radial leakage caused by axial gap and axial leakage caused by radial gap, the paper discussed the changing in mechanism of axial and radial, which can solute these impactions. Analyzed the backpressure and the back-press port position of back-press technology, Which is the best used.

针对涡旋压缩机工作过程中压缩腔内产生的气体力对整机造成的轴向间隙的径向泄漏和径向间隙的轴向泄漏问题，讨论了解决这些影响的轴向随变机构和径向随变机构，对使用最多的背压技术进行了背压力及背压孔开设位置的分析。

Flap valve pin and WA44C Type Pound-Grade Balance Bellows Spring-Loaded Safety Valvevalve shaft axial clearance between the bearing face not less than 0.25mm.

阀瓣轴销与阀体支承端面之间的轴向间隙不应小于0.25mm。

Flap valve pin and WA44C Type Pound-Grade Balance Bellows Spring-Loaded Safety Valve valve shaft axial clearance between the bearing face not less than 0.25mm.

阀瓣轴销与阀体支承端面之间的轴向间隙不应小于0.25mm。

Chrysanthemum of 10 thousand birthday is lax to edaphic requirement, with the arenaceous qualitative loam with fecund, good drainage had better.

万寿菊对土壤要求不严，以肥沃。排水良好的砂质壤土为好。

He unstepped the mast and furled the sail and tied it.

他拔下桅杆，把帆卷起，系住。