真空处理

The treating plant mainly has the following input signal in this set of control system: Che Neinei was mad that outside the temperature signal, the vehicle the external Qi temperature signal, the water temperature temperature signal, the air blower feedback signal, the mix air throttle feedback signal, the back light lamp signal and so on, the output device is the VFD fluorescence vacuum display monitor, the control device is mainly on control panel''s pressed key, realizes the plan acts according to the vehicle speed, Each temperature value''s situation comes the intelligent control air-conditioning system various air throttles electrical machinery and compressor''s work, causes in compartment''s temperature basis hypothesis temperature in the physical sensation comfortable scope, simultaneously controls the blowing through the air throttle electrical machinery''s movement the direction, the cold hot blast proportion, the automatic control, forces to defrost, the inside and outside circulates the wind transformation and the breakdown situation demonstration is the concrete function which this set of control system can realize.

在这套控制系统中处理装置主要有以下输入信号：车内内气温度信号、车外外气温度信号、水温温度信号、风机反馈信号、混合风门反馈信号、背光灯信号等，输出装置为VFD荧光真空显示屏，控制装置主要是控制面板上的按键，实现的方案是根据车速，各个温度值的情况来智能控制空调系统各风门电机和压缩机的工作，使得车厢内的温度根据设定温度在人体感觉舒适的范围之内，同时通过风门电机的动作来控制吹风的方向、冷热风的比例，自动控制，强制除霜，内外循环风的转换和故障情况的显示都是这套控制系统所能够实现的具体功能。

He metabolism process that ear candles apply is that one end to put into ear hole and another end to be lighted, under theory of vacuum, the Heat energy produced will gradually enter the ear, loose the Earwax and eliminate the pore's waste.

耳烛运用的代谢过程将经过处理的耳烛，一端放入耳洞，另一端点火，它运用真空负压的原理，通遇热产生热能，利用燃烧所产生的热气慢慢进入耳内，松动耳垢并清除毛孔之废弃物并自然排除。

The main production equipment are Japan's Mitsubishi machining center, CNC milling machine, precision grinder, inner circle of large vertical mill and high-precision wire-cutting and other types of vehicles, milling, grinding, drilling and other equipment; the main heat-treatment equipment has automatic vacuum quenching processing equipment; HR150-A Rockwell Hardness Tester, etc..

主要生产设备均采用日本三菱加工中心、数控铣床、精密磨床、大型立式内圆磨和高精度线切割以及其它各类车、铣、磨、钻等设备；主要热处理设备有全自动真空淬火处理设备；HR150-A洛氏硬度计等。

The strong accelerating field is required at the surface of photocathode in RF cavity.

以及关于金属与金属化合物阴极在真空中提高量子效率的处理方法和有关实验结果的分析。

The results show that G. ficorum can be killed completely at lower dosage of methyl bromide and in short time under vacuum condition. It provides a new method for treatment of pests in flower.

结果表明，在真空条件下，仅需要较低的熏蒸剂量在较短的时间内即可全部杀死榕树盆景里的榕管蓟马，杀虫效果达100%，达到快速、高效、安全、环保的要求，为花卉害虫的处理提供了一种新的方法。

Based upon the data of modal analysis for the plate in vacuo by finite element method and properly dealing with the integral at sin-gularity, the value of NAVMI is obtained by discretizing the integral.

在真空中模态的有限元方法分析数据以及采用适当方法处理奇点积分的基础上，应用离散积分计算了无量纲附加虚质量增量的值。

We used different methods to calculate luminosity in order to assure its reliability. Structure function method is adopted to derive the radiatively corrected cross section whose accuracy is up to 1%. The corrections from vacuum polarization and effect of energy spread are also studied. The final analytical approximation formulaes of the observed cross sections are worked out. Different fitting methods are carried out to fit the resonances according to different requests.

模拟的分布图的仔细对比，并兼顾实验的要求，得到每种事例对应的选择条件，特别是在处理积分亮度时，更是采用了不同的方法，以保证亮度计算的可靠性；采用结构函数的方法推导出截面的辐射修正公式，精确度达到了1％的水平，研究了真空极化给拟合公式带来的修正，并考虑了束流能散的影响，计算出最终的观测截面的解析近似式；对于三个共振态的拟合，针对不同的要求，采用了不同的拟合方法；同时在M.C。

All 925 German high antioxidant silver material, and introduces the most advanced cutting-edge technology of vacuum plasma treatment, as palladium and rhodium.

全部采用德国高抗氧化925银料，并引入最先进的真空离子尖端技术经钯铑处理。

Chrysanthemum of 10 thousand birthday is lax to edaphic requirement, with the arenaceous qualitative loam with fecund, good drainage had better.

万寿菊对土壤要求不严，以肥沃。排水良好的砂质壤土为好。

He unstepped the mast and furled the sail and tied it.

他拔下桅杆，把帆卷起，系住。