极限位置

One should pay attention to the problem of direction in the stiffness matrix of a tapered element.

若没有考虑到任一构件中可能形成塑性铰的位置，就不能准确地预测梁柱真实的极限承载能力。

An extremely high temperature of anode humidification is also unreasonable; as a result, when the current density is high, the liquid water should be injected directly into anode gas channel to guarantee both high inlet H〓 concentration and well-humidified membrane. 4. The utilization of Pt in the cathode catalyst layer will decrease with the increasing current density; as a result, based on the principle of maximal Pt utilization, the catalyst layer can be designed much thinner or not uniformly in the catalyst distribution.

而在此截面上，交指型流场燃料电池阳极侧的液态水饱和度的极值位置并不确定；在电池阴极处，液态水饱和度的极值总是出现在z=0.002m处的气体扩散层和膜的界面上，并且该处的液态水饱和度沿x方向存在一个最大值，与此相应的氧气的质量浓度分数在该处达到极小值，因此极限电流密度将首相出现该处，但总体来说液态水饱和度沿x方向的分布较为均匀。4。

When a nesting level is provided, the instruction stores the pointer to the beginning of every currently active stack frame in the procedure's stack frame.

当层数未达到极限允许嵌套时，指令存储指针到程序堆栈结构中每个活动的堆栈的起始位置。

In the thermodynamic limit, the zeros accumulate nearly the transition point z_0 in the real axis and the density of zeros near z_0 determines the order of the phase transition.

在热力学极限下，配分函数零点在正实轴上集聚的那些点z_0给出了相变的位置，同时在z_0附近的配分函数零点密度决定了相变的类型。

Under the conditions that the concrete expression of its singularities are not sloved,we discuss the bounded property of trajectories, separatrix configuration,nonexistence and existence of limit cycle.

对一类多分子反应模型x＝1－αx－xpyq，y＝βy（xpyq－1－1）进行定性分析，在第一象限奇点无法具体求出的条件下，讨论了轨线的有界性，分界线的位置关系以及极限环的存在性和不存在

Apart from the working limitations resulting from its structural property, the flat plate heat pipe carries out heat dissipation through the evaporation and condensation of the working fluid. Thus, if the working angle of the fluid is adverse to its backflow, the heat pipe will fail easily. Furthermore, not the orientations of all the heat sources are favorable to the functioning of the heat pipe. To compensate for this drawback, this research focuses primarily on the development of a composite structure which will reduce the effect of gravity on the working fluid. Generally speaking, the heat pipe is divided into three main categories: the groove type, sintered metal type and mesh screen type, as shown in Table 2. As far as capillary force is concerned, the sintered metal type and mesh screen type show better performance. As mentioned in R.

平板式热管除了因其结构特性而产生的工作极限之外，由于其作用乃是透过工作流体的蒸发及凝结进行散热，故若是其工作角度不利于液体之回流，便容易使热管失效，且并非所有之发热源都是位于有利于热管工作之位置，因此本研究之主要目的为设计一可减少重力对工作流体影响之复合式结构；一般而言，热管之结构大致可分为沟槽、烧结及网格三种(如表2所示)，其中烧结及网格结构有较佳之毛细力，在 R。

Keywords:double load cells technique; self-balanced; ultimate bearing capacity; loading sequence; embedding position

关键词］双荷载箱技术；自平衡；极限承载力；加载顺序；埋设位置

Since historical times,England ,where the early inhabitants were Celts, has been conquered three times .

从有历史以来，英国，在此地早期居住的是凯尔特人，已经被征服了三次。

Bluetooth OBEX File Transfer Enables the sending and receiving of files on your phone via Bluetooth.

蓝牙OBEX文件移动允许经过蓝牙传送和接受文件。。。。