夹紧

An operation lever displaceably pressed by the engagement piece for operation to operate the rope gripping mechanism is connected to the rope gripping mechanism.

绳索夹紧机构上连接有工作用杆，该工作用杆用于通过被工作用卡合件按压移动来使绳索夹紧机构工作。

This design is to dials forks the components the processing craft and the jig design, its components are the forging, has the volume to be small, components complex characteristic,Because the surface is easier than the hole to process, when formulation technological process, first the machined surface, then processes other take the surface as the datum,In which various working procedures jig all uses the unit clamp, special regarding processes the big end of hole, the trough and drills the capitellum hole incline eyelet in the working procedure, Chooses locate mode which two sells at the same time, and operates the simple manual clamp way clamp, its organization design is simple, the convenience also can satisfy the request.

此次设计是对拨叉零件的加工工艺和夹具设计，其零件为锻件，具有体积小，零件复杂的特点，由于面比孔易加工，在制定工艺规程时，就先加工面，再以面为基准来加工其它，其中各工序夹具都采用专用夹具，特别的对于加工大头孔、槽和钻小头孔斜面小孔的工序中，选一面两销的定位方式，并以操作简单的手动夹紧方式夹紧，其机构设计简单，方便且能满足要求。

This design is to dials forks the components the processing craft and the jig design its components are the forging has the volume to be small components complex characteristicBecause the surface is easier than the hole to process when formulation technological process first the machined surface then processes other take the surface as the datumIn which various working procedures jig all uses the unit clamp special regarding processes the big end of hole the trough and drills the capitellum hole incline eyelet in the working procedure Chooses locate mode which two sells at the same time and operates the simple manual clamp way clamp its organization design is simple the convenience also can satisfy the request.

此次设计是对拨叉零件的加工工艺和夹具设计，其零件为锻件，具有体积小，零件复杂的特点，由于面比孔易加工，在制定工艺规程时，就先加工面，再以面为基准来加工其它，其中各工序夹具都采用专用夹具，特别的对于加工大头孔、槽和钻小头孔斜面小孔的工序中，选一面两销的定位方式，并以操作简单的手动夹紧方式夹紧，其机构设计简单，方便且能满足要求。关键词拨叉，加工工艺，专用夹具，设计

The biggest characteristic of this model is that the hydraulic system pump station, operating console and working clamp installation table can be installed and connected in users sites and dived the test workpiece into the pond, can lift up and down, left and right two directions clamp worktables set 90 degree overturn function, especially suitable for gas pressure test.

本机型最大特点由液压系统泵站，操作控制台和工作夹紧装置台在用户现场安装连接，将试验工件潜入水池中目测，可上下升降，左右两向夹紧工作台设有90度翻转功能，特别适应气体压力试验。

The counterbore at the crankcase joint line is to ensure that the stresses are distributed over a larger area in order to even out the clamping loads on the joint faces(line of max stress is at 45 degrees) this means that the clamping loads loads can ideally overlap at the joint face it also has the bonus of giving a longer bolt length which means less stress on the bolt for the same tightening torque.

该counterbore在曲轴箱的联合路线，是要确保该讲是分布面积较大，在以，甚至出夹紧载荷对联合所面临的（线的最高强调的是，在45度），这意味着，夹紧载荷载荷可以理想重叠在联合面对它也有奖金给予较长的螺栓的长度即减少应力对螺栓同时收紧扭矩。

Based on above process, three parts of cricoid winding machine's structure is defined as that: winding installation, clamping installation and the part of chest. The clamping installation clamp loop and let it turn. Install the wheel which fit the strap and a impulse electric in the the part of chest.

基于前面所提到的工艺动作和路线又作了进一步的确定，也就是说该环型缠绕机结构又可分为绕线装置、夹紧芯模并且带其转动的夹紧装置和安装带轮以及步进电机的箱体三大部分。

This design takes the diesel cyclinder tank for the clamping and locating device of tank boring and designing the clamping regulations of arts and crafts of tank, we take two cylinders and one face to locate which can limit six free dgrees In order to reduce errors of tank during processing,we take standard and concurrent principle,unify principle,principle with each other for basis and selection of rough basis into order to make the orientation tight enough,it is required to insist in the principle of using the unrepeated coarse beach mark as possible as you can.

本设计以柴油机汽缸箱体为例，对箱体镗孔的夹紧和定位装置进行工艺分析和夹具的设计。在对此箱体的工艺规程采用两销一面对其进行定位以限制其六个自由度。为减少箱体在加工过程中的误差，我们考虑基准的重合原则，统一原则，互为基准原则以及粗基准的选择原则，为使定位稳定夹紧可靠，要求所选用的粗基准尽可能不重复使用原则。

It's fixed by swing depressor fixtume structure thedespower can be assured by checking computations.

在前述定位基准面选择的前提下，用摆动式压板杠杆夹紧结构，夹紧力经验算可以保证。

It's fixed by swing depressor fixtume structure the despower can be assured by checking computations.

在前述定位基准面选择的前提下，用摆动式压板杠杆夹紧结构，夹紧力经验算可以保证。

This design introduced the bulldozer with the edge board in the machining center the drill hole jig design and the simulation elaborated the bulldozer with the edge board in the machining center the drill hole jig design is mainly designs jig's positioning device the clamp and the jig body's structure according to the edge board structure shape selects jig various components according to the edge board's material the material carries on the intensity examination has realized jig's in processing localization and the clamp function.

本设计介绍了推土机用刃板在加工中心上钻孔的夹具设计与仿真，阐述了推土机用刃板在加工中心上钻孔的夹具设计，主要是根据刃板的结构形状来设计夹具的定位装置、夹紧装置和夹具体的结构，根据刃板的材料来选用夹具各零件的材料，进行强度校核，实现了夹具在加工中的定位和夹紧作用。

Objective: To study the effect of polycythemia on blood oxygen saturation.

裴蕾目的：观察RBC剧增而引起的高粘血症对血氧饱和度的影响。

Based on SIMPLER algorithm in the curvilinear body-fitted coordinates, the calculations were performed for Pr=0.7, Re=10~1000 on non-orthogonal non-staggered grids which are generated by elliptic equation systems.

采用曲线坐标系下压力与速度耦合的SIMPLER算法，数值研究了周期性渐扩渐缩波纹通道内脉动流动与换热情况，流动Re数的范围为10~1000，Pr数为0.7。