夹紧

4 CONTAINER LOCKING TO THE BASEPLATE During the rolling process, the container is clamped to the baseplate by means of four hydraulic clamping devices.

最好的翻译 1.4 对 BASEPLATE 的容器锁定在旋转程序的时候，容器被夹紧到 baseplate 经由四水力的定位装置。

Series of bevellers are hydraulic pressure drove, equipped with hard alloy cutter.

系列倒棱机床，采用液压自定心夹紧，液压可转位挡料器挡料，硬质合金刀切削。

Imagine clamping thin sheet that requires a chamfered perimeter and chamfered opening in its center.

试想夹紧薄板，需要倒角周边和倒角开放的中心。

Circlips for shaft/hole; open grip rings; steel wire circlips; round wire snap rings; spring washers with internal teeth, external teeth, curve, wave; external tap round nuts, external tongue round nuts with long tap, external tongue round nuts with long tap and wing, etc; motorcycle accessories, auto transmission shaft rings, non-standard fasteners.

我公司按国际生产孔用挡圈，轴用弹性挡圈，开口夹紧挡圈，钢丝挡圈，DIN471 DIN472 DIN6799，特大挡圈200-800，厚度不限。各种内齿，外齿垫圈。鞍形，波形，推型弹性垫圈，各种规格型号的弹簧垫圈，不锈钢弹簧垫圈。以及单耳，双耳外舌园螺母等，摩托车配件，各种汽车传动轴卡簧及非标准件

Crimp a blue butt connector on each bare wire using the wire crimpers.

对每一个裸压接导线夹紧器使用蓝色线对接连接器。

It has even developed an idea for a four-sided tombstone that would have magnets on the two wide faces and standard T-slots on other two faces for parts that require standard clamping methods.

它甚至建立了一个想法，任期四年，片面墓碑，将磁铁的两个宽面孔和标准T型槽的其他两个方面的部分要求标准夹紧方法。

Pacific Valves can provide either impact handwheels or clampon hammer blow handwheel adapters.

美国太平洋阀门公司即可提供冲击手轮，也可提供夹紧式锤击手轮接合器。

This project is design the 50# knife hilts broach mechanism.It is cutting tool automatically clamp mechanism of spindle's inside for large-scale machining .

50＃刀柄拉刀机构为大型机床主轴内部刀具自动夹紧机构。

When cutting tool roaled of spindle's hole by manipulator or other ways,the pull nail behind of knife hilts is sent to ahead of tension bar of spindle. When receives the clamps signal, the pressure oil is passed over the oil cylinder left cavity of the spindle rear part, the piston to the right migration ,tension bar also to right migration by small dish shape spring function, the stell ball of ahead circumference of the tension bar shrink the distribution diameter by spindle's cone hole's force, holds on the knife hilts and pull nail colsely.

当刀具由机械手或用其他方法装到主轴孔后，其刀柄后部的拉钉便被送到主轴内拉杆的前端，当接到夹紧信号时，将压力油通入主轴尾部的油缸左腔，活塞向右移动，拉杆在碟形弹簧的作用下也向右移动，其前端圆周上的钢球在主轴锥孔的逼迫下收缩分布直径，将刀柄拉钉紧紧拉住。

The lathe chuck is used for chucking the work,that is for clamping it so that it will rotate without wobbling while turning.The chunk,usually mounted on the headstock spindle,may have differnt sizes and construction.

车床卡盘用来夹紧工件这就是夹具，当工作台转动时夹具将旋转摇摆，卡盘通常安装在主轴箱心轴上可能会有不同的大小和结构。

Since historical times,England ,where the early inhabitants were Celts, has been conquered three times .

从有历史以来，英国，在此地早期居住的是凯尔特人，已经被征服了三次。

Bluetooth OBEX File Transfer Enables the sending and receiving of files on your phone via Bluetooth.

蓝牙OBEX文件移动允许经过蓝牙传送和接受文件。。。。