合金

Suitable metals and alloys include aluminium, bronze, beryllium, chromium, columbium, constantan, copper and copper alloys, gold, nickel and nickel alloys, lead, magnesium, molybdenum, niobium, platinum, silver, stainless steel, mild steel, tin, titanium, tungsten, vanadium, zinc and zirconium.

适用于金属和合金包括铝，铜，铍，铬，铌，镍铜合金，铜及铜合金，金，镍和镍合金，铅，镁，钼，铌，铂，银，不锈钢，低碳钢，锡，钛，钨，钒，锌，锆。

Under the protection of fusing agent or gas, melting commercial-purity magnesium completely in copple, adding alloying element in formation of Al-Be hardener, commercial-purity aluminum, Al-Mn hardener, Mg-Re hardener and commercial-purity antimony, agitates to achieve uniform mixing, refining and casting.

在熔剂或气体保护熔炼条件下，工业纯镁在坩埚中完全熔化后，分别以Al-Be中间合金、工业纯铝、Al-Mn中间合金、Mg-Re中间合金，工业纯锑的形式加入合金化元素，搅拌混合均匀并进行精炼后浇注。

The local ordered CoPt〓 Ll〓 phase with good FCC (111) crystalline orientation, which exists at the interfaces of multilayers and in alloy films, was considered to contribute to the PMA in Co/Pt multilayer and Co-Pt alloy films. But the appearance of large amount of ordered CoPt〓 Ll〓 phase or completely disordered Co-Pt phase will result in the decrease in PMA.

Co/Pt多层膜界面处或Co-Pt合金膜中具有FCC（111）织构特征的局部有序CoPt〓 Ll〓合金相的形成被认为可能会对多层膜和合金膜中的垂直磁各向异性作出贡献，但大量CoPt〓 Ll〓有序相或大量完全无序Co-Pt合金相的生成都会导致垂直各向异性的下降。

With increasing La content, however, the phase structure of the alloys 〓(x=0.03-0.1) can be changed from C15 to C14, but that of the alloys 〓(x=0.03-0.1) has not still changed, and the second phase of both alloys decreases. Some diffluent phase appear on the surface of both alloys, because there some holes on the surface of alloys after corrasion.

结果发现，在低La含量时，两种合金均保持原有的相结构，但合金表面存在少量易溶相，在样品制备中由于腐蚀合金表面出现孔洞，合金的活化性能和放电容量得到提高。

The company has vertical semi-continuous casting production lines, capable of producing all kinds of diameter of the circle and a square with deep processing of high-quality magnesium alloy billets deformation; extrusion production line can produce all types of magnesium alloy extrusion sacrificial anode, the sacrificial anode aluminum, zinc alloy sacrifice Anode and a variety of magnesium alloy extrusion products.

公司拥有立式半连续铸造生产线，能够生产各种直径的圆形和方形高品质深加工用变形镁合金坯料；挤压生产线可生产各类挤压镁合金牺牲阳极、铝合金牺牲阳极、锌合金牺牲阳极和各种镁合金挤压产品。

Morphology of Sn-0.7Cu and Sn-3.5Agpowders, the course of mechanical alloying and the effect of ball milling conditionson the formation of mechanical alloy were analyzed using a scanning electronmicroscope, a differential thermal analyzer and an X-raydiffractometer.

利用扫描电镜、差热分析仪、X 射线衍射仪对 Sn-0.7Cu、Sn-3.5Ag 合金粉末的形貌、机械合金化进程、球磨条件对机械合金化合金相的影响、机械合金化 Sn-0.7Cu、Sn-3.5Ag 的反应机制进行了研究。

The results show that the number of insoluble constituents and dispersoid particles in alloys increase with increase of Mn content, the former is detrimental for the specific elongation of alloys, and the latter impedes recrystallization during solution treatment.

研究结果表明：提高合金中的Mn含量，可增加合金中不可溶结晶相及弥散相粒子的数量，前者对合金的延伸率不利，后者阻碍了合金固溶处理过程中的再结晶。

The results show t hat yttrium exists as the form of compound (Al2Y) in AZ31 magnesium alloy, and dystectic Al2Y as the heteromorphic nucleation emerges firstly in the cou rse of alloy precipitation, which refines the alloy's microstructure and obviou sly improves the mechanical properties at room and high temperature. The average grain size of AZ31 magnesium alloy containing Y is reduced by 35.82%. Tensile s trength, yield strength and elongation percentage reach 212 MPa, 147 MPa, and 7. 5% at room temperature respectively, and 117 MPa, 98 MPa, and 10.2% at 200 ℃ re spectively.

结果表明，Y在AZ31 镁合金中主要以块状Al2Y化合物形式存在；高熔点的Al2Y在合金凝固过程中首先析出，成为凝固的异质形核剂，从而细化了合金组织，改善了室温和高温力学性能；由于Y的强化，含Y AZ31镁合金平均晶粒尺寸降低幅度约为35.82 %；室温抗拉强度、屈服强度和延伸率分别为 212 MPa， 147 MPa和7.5%，200 ℃时分别为117 MPa， 98 MPa和10.2%。

By means of scanning electron microscopy , transmission electron microscopy and X-ray diffraction techniques, microstructure of spray-deposited hypereutectic Al-Si alloy was analyzed.

本文以过共晶Al-Si合金为研究对象，在对喷射沉积合金凝固过程分析的基础上，重点研究了合金的微观组织与力学行为，讨论了后续热挤压和热处理对喷射沉积合金微观组织和力学性能的影响。

About the Calculation of Arc length of the Oriented Smoth Curve or Jordan;2. The experimental results show that the optimum melting voltage is 35～36 V,the reasonable arc length is 25～29 mm.

以海绵钛和中间合金压制的电极经两次熔化得到的TC11合金铸锭为原材料，采用真空自耗电弧炉，在不同的电压下熔炼3次TC11合金铸锭，研究熔化电压、弧长与TC11合金铸锭扒皮深度和扒皮量的关系。

The big eared hedgehog, the little owl, the sand gecko, the three-toed jerboa, and every show needs a villain - saw-scale - the viper!

大耳刺猬，小猫头鹰，沙壁虎，三趾跳鼠，每场戏都需要反派角色：蝰蛇。

Plasmodiophora brassicae ; resting spores ; density gradient centrifugation of sucrose ; ultrasonic disruption

根肿；休眠孢子；蔗糖密度梯度离心；超声波破碎