可成形的

Paste : The powdered or granulated incense material is mixed with a sticky and incombustible binder, such as dried fruit , honey , or a soft resin and then formed to balls or small cakes. These may then be allowed to mature in a controlled environment where the fragrances can commingle and unite.

香团：粉状或颗粒状的香原料用不易燃的带粘性的物质混合而成，例如干的果实，蜜，或软的树脂，粘合成球状或小块，然后放在可控的环境下使各种芳香充分地混合成形。

This paper studied the calculating method of the spiral-fluted tube's spinning force, which can provide basic theory for designing spinning shaping equipemnt, establishing spinning shaping technology and designing spinning tools.

摘 要：研究了薄壁圆管螺旋槽旋压成形时力的计算方法，可为设计旋压成形设备、编制旋压工艺、设计旋压工夹具提供理论依据。

The technology of bending by bendable roller was introduced briefly. A finite element model of the process of BBBR was built by the general finite element program.

简单介绍了可弯曲辊卷板成形技术，利用通用有限元程序建立了可弯曲辊卷板成形过程的有限元模型。

Methods selective and limited minimally invasive debridement under arthroscope was applied to 54 patients with osteoarthritis of knee joint; hyperplasia of inflammatory synovial membrane and abrasion of anterior cruciate ligament were chipped or vaporized with radiofrequency, the corpus liberum were taken out, cartilage was scoured into certain shape; excision or partial excision were performed to hyperplastic intercondyloid spine, osteophyma and menisci; intercondyloid fossa was formed.results 45 cases were followed up for an average of 18 months (from 6 months to 24 months); the clinical symptoms of most cases released obviously and the joint function improved.conclusions minimally invasive debridement under arthroscope can effectively release oa symptoms, improve joint function and raise the quality of life.

对54例膝关节骨性关节炎患者进行关节镜下选择性、有限化微创清理术。手术内容包括刨削或射频汽化增生的炎性滑膜组织和前交叉韧带磨损、游离体取出、软骨打磨成形、增生髁间棘切除、部分骨赘切除、半月板部分切除、髁间窝成形。结果随诊45例，平均18个月（6～24月），大多数患者临床症状明显缓解，关节功能改善。结论关节镜微创清理术可有效缓解oa症状，改善关节功能，提高生活质量。骨关节炎；膝关节；关节镜检查

To use the well-developed inspection technology, two problems are solved. First, a crank-rocker mechanism is designed to put up and down the probe; and then an output interface equipment is built, which enables the operator observe the measurement results on time, by the communication between the pachometer and the output interface equipment.

考虑利用已成形的测厚技术，本文主要解决了两方面问题：机械上设计了曲柄摇杆机构实现了测厚探头的自动抬放；通过设计输出接口显示装置，利用它与测厚仪之间的通讯实现了测量数据的远距离传输，保证了操作者可实时观测到测量数据。

Finally, simulation software was developed with Visual C++ and Delphi for 2D molding analysis of MIM, which affords facilities for the quality forecast of 2D thin wall parts and optimal design of mold and process parameters. In the research of molding performance of MIM feedstock, for the shortcoming of capillary rheometry, it was propounded that using spiral mold test molding performance of feedstock, and a set of spiral mold was creatively designed with quickly exchange gates and closed mold cavity. With the spiral mold, an orthogonal experiment was made on getting regress equation of flow length L〓 of the heavy alloy feedstock. Then the rule of L〓 varying with Q〓, P〓, and ΔT〓 was discovered. Q〓 ranks first in the influence on process parameters of molding performance, P〓 and Δ T〓 second. Therefore the injection rate Q〓 should be controlled primarily to improve the flow performance of feedstock.

在MIM喂料注射成形性能研究方面，针对毛细管流变仪测试法衡量流动性能的不足，提出使用螺旋线模具测试喂料熔体的注射成形性能，创造性地设计了一套可快换浇口，模腔封闭的螺旋测试模，并在螺旋测试模上采用正交实验设计，得出了高密度重合金喂料流动长度L〓的回归公式，揭示了L〓随Q〓、P〓、△T〓和S〓的变化规律，并得出工艺参数对成形性能影响的强度顺序为Q〓最大，P〓与△T〓其次，因而改善喂料流动性能应优先控制注射速率Q〓。

From the angle critical force ,this thesis analyses the stability of the formation of axle shaft spline in the extrusion and the calculation of the constraints available after losing stability.

从临界力的角度入手分析花键半轴在挤压成形时的稳定性及失稳后可增加约束的计算，研究表明半轴花键实现精密挤压成形不稳定时可增加约束来解决失稳问题。

Aiming at simpling the structure of numerical control system, and decreasing the cost and difficulty of development, a numerical control system based on the programmable logic controller was designed for a stereolithography apparatus machine with utilizing the prominent feature of the easy development and higher reliability of the PLC.

为简化光固化快速成形数控系统的结构、降低系统开发的成本和难度，结合所设计的成形设备特点，利用可编程逻辑控制器具有的开发简单、性能可靠等优点，设计了一个基于PLC的光固化快速成形数控系统。

In the research of visual simulation software development, in order to build the software system model and flow analysis algorithm based on Cross-WLF viscosity model, and realize functions such as pre-processor, solver, parameter regress, data management, graph operations, some advanced software methods as OOSE (Object Oriented Software Engineering) and UML were applied to set up user model, static model and dynamic model of MIM simulation software. These models describe system function, event flow, structure and relation of classes, object interaction, structure of database and I/O file format.

在MIM喂料注射成形性能研究方面，针对毛细管流变仪测试法衡量流动性能的不足，提出使用螺旋线模具测试喂料熔体的注射成形性能，创造性地设计了一套可快换浇口，模腔封闭的螺旋测试模，并在螺旋测试模上采用正交实验设计，得出了高密度重合金喂料流动长度L_m的回归公式，揭示了L_m随Q_m、P_m、△T_m和凡的变化规律，并得出工艺参数对成形性能影响的强度顺序为Qm最大，尸m与△几其次，因而改善喂料流动性能应优先控制注射速率Qm。

It according to rotates divides into the positive rotation for the direction and the semi finished materials material flow direction similarities and differences and instead turns on lathe, including turns on lathe, the stable spinning and finally turns on lathe three stages.

其按旋轮进给方向与毛坯材料流动方向的异同分为正旋和反旋，包括起旋、稳定旋压和终旋3个阶段，成形中的工件可划分为3个区域，即未成形区、成形区和已成形区，材料所受到的应力、应变在不同阶段也具有不同的特点。

Since historical times,England ,where the early inhabitants were Celts, has been conquered three times .

从有历史以来，英国，在此地早期居住的是凯尔特人，已经被征服了三次。

Bluetooth OBEX File Transfer Enables the sending and receiving of files on your phone via Bluetooth.

蓝牙OBEX文件移动允许经过蓝牙传送和接受文件。。。。