压力喷嘴

As a result, low altitude operation is characterized by the appearance of a series of alternating pressure peaks and valleys along the nozzle surface.

因此，低空运作的特点是出现了一系列的交替的压力，高峰和低谷沿喷嘴表面。

The process then repeats itself, setting up an alternating series of high- and low-pressure zones on the nozzle wall.

然后，这一进程重演，设立一个交流的一系列高，低压力区的喷嘴墙。

Our company besides produces the above standard throttling gear, but also produces the present domestic ordinary application each kind of special throttle, like wing anemography installment, ring-like throttle type flowmeter, double repeated passage hamlet anemography installment, 1/4 round spray nozzle, segment of orifice, dual orifices, Inner Tibet orifice, fast tube Flow sensor, jack-in low damaged due to pressing flowmeter, against wall wind pressure thief and so on 30 many kinds of varieties, 1000 many kinds of specifications, caliber from DN10-3000mm, pressure from PN0.01-32MPa, temperature from negative 260℃- 550℃.

我公司除生产上述标准节流装置外，还生产目前国内普通应用的各种特殊的节流件，如机翼型测风装置、环状节流式流量计、双重文丘里测风装置、1/4圆喷嘴、圆缺孔板、双重孔板、内藏孔板、均速管流量传感器、插入式低压损流量计、防墙风压取样器等30多种品种，1000多种规格，管径从DN10-3000mm，压力从PN0.01-32MPa，温度从负260℃-正550℃。

The discussion is focused on the determination of the minimum air rate when there is reservoir fluid influx during air drilling, injection pressure at standpipe, and bit nozzle pressure.

应用气体状态方程、热力学定律对空气钻井中各个流动参数进行分析，重点讨论储层流体涌入时空气钻井过程中最小空气流量的确定，以及立管注入压力和钻头喷嘴压力等问题。

Moreover, the hot compressive deformation behavior of the RS/PM AZ91 magnesium alloy and AZ91 alloy matrix composite were also investigated, the conclusions are drawn as follows:1. The processing parameters of the atomization-twin rolls quenching technology were optimized as follows: the diameter of the nozzle 1mm, the wheel velocity 25m/s, the pressure of atomization gas 0.3MPa and Ar gas for melt injection 0.1MPa. The RS AZ91 alloy flakes exhibited fine and uniform microstructures. When the flakes were extruded at 673K, extruded velocity of 0.1mm/min and extrusion ratio of 25:1,the magnesium alloy rods with clean surface, uniform dimension and excellent mechanical properties were obtained.2. The RS AZ91 magnesium alloy powders prepared by atomization-twin rolls quenched technology exhibited fine equiaxed grains with the grain size of 1-3μm, the phase constituent included supersaturate solid solution phaseα-Mg and miner fineβ-Mg_(17)Al_(12) phase. The as-extruded materials also exhibited equiaxed grains with the size of 5-7μm and a large number of fineβ-Al_(12)Mg_(17) and fewer AlMg_2Zn phases were detected in the alloy.

本文还研究了快速凝固/粉末冶金AZ91镁合金热压缩变形流变应力行为，快速凝固/粉末冶金法原位生成Mg_2Si增强AZ91镁基复合材料，经过系统的研究，获得如下结论：1、雾化-双辊急冷法在下列工艺参数组合下：双辊线速度25m/s；喷嘴直径1mm；熔体压射压力0.1MPa；雾化气体压力0.3MPa。，可获得宏观尺寸细小、微观组织均匀细小、综合性能优良的的快速凝固AZ91镁合金细碎箔带，快速凝固箔带在挤压温度为673K、挤压速度为0.1mm/min，挤压比为25：1时，可获得的外表光洁、尺寸均匀、组织性能优异的镁合金棒材。2、雾化-双辊急冷法制备的AZ91镁合金粉末态为细小等轴晶组织，晶粒尺寸1-3μm，组织为α-Mg过饱和固溶体和微量的细小β-Mg_(17)Al_(12)相组成；粉末挤压棒材为等轴晶组织，晶粒尺寸5-7μm，组织中含有大量细小的β-Al_(12)Mg_(17)以及AlMg_2Zn析出相，室温力学性能，抗拉强度383MPa，屈服强度275MPa，断后伸长率7.5%。

Test data collected by 90°are inlet nozzle test unit is instroduced ,according to international standard,Test data such as inlet and outlet pressure,fan pressure,efficiency and etc.are computed.

介绍了用90°弧形进口喷嘴试验装置采集试验数据，再根据国际标准对风机的进出口压力、通风机压力、效率等试验数据进行了计算。

Input is simply a list of propellant ingredients, as well as chamber pressure and nozzle exit pressure.

投入，简直是名单推进剂成分，以及商会的压力和喷嘴出口的压力。

P e and P o are the nozzle exit pressure and the chamber pressure, respectively.

p e和P O的喷嘴出口的压力和会议厅的压力，分别。

Nozzle pressure switchover is improved over hydraulic pressure as the compressibility of the melt cushion is avoided.

喷嘴压力转换比液压缸压力转换好的地方是避免了用于缓冲的熔融塑料的可压缩性。

The pump pressure should be reduced to more of a steady flow instead of a fine spray.

水泵压力应该降低，保持耦合水以稳定的流速流出要比高压力的水从细小喷嘴中喷出效果好得多。

Since historical times,England ,where the early inhabitants were Celts, has been conquered three times .

从有历史以来，英国，在此地早期居住的是凯尔特人，已经被征服了三次。

Bluetooth OBEX File Transfer Enables the sending and receiving of files on your phone via Bluetooth.

蓝牙OBEX文件移动允许经过蓝牙传送和接受文件。。。。