分析校准

The paper analyzed influence of temperature upon metatitanic acid density and has found a correction method for densitomeler using re-gression equation of temperature and density ,they determined and verified the empirical constant for conversion equation of the slurry demsity and concentration with physical and chemical method.

分析了温度对偏钛酸比重的影响规律，找出利用温度和比重的回归方程校准比重计的方法，同时利用物理和化学方法，确定和验证了浆料比重与其浓度换算规律的经验常数，结果令人满意。

The studies of hydrogen behaviour in HR-1 stainless steel and its composite sample with CVD coated chromium oxidic film have been presented.

本文介绍氢在HR－1不锈钢基体及镀有氧化铬膜的复合材料中的行为研究，包括基体的准备；膜的制备；用不同手段从不同角度对膜进行的分析测试；膜与基体之间的平均结合力测定；用不锈钢材料构成的高温低压渗透回路的建造、调试、密封性能校准；纯HR－1基体材料中的氢渗透规律研究；有膜复合材料中氢的稳态迁移过程的表现规律实验结果。

Discussed the uncertainty of vibration transducer calibration and vibrometer itself overall.

最后对校准系统和相位型测振仪测量的不确定度给予了全面的分析。

Different calibrating lenses are designed, and simulation is made to the system calibration.

对各种校准镜进行了设计，并对系统标定进行了模拟分析。

Each of the filter calibration standards have been analysed 5 times using Electroformed sieves traceable to NIST and NPL.

每中过滤校准标准颗粒都会用电铸筛，根据 NIST 和 NPL 分析5次。

The uncertainty evaluation of measuring results about indicator error of digital dial gauge 0~25 mm was analyzed in this article,those indicated that it was feasible using TWIN-CHECK1200 length measuring machine as calibration tools.

介绍了0~25 mm 数显千分表的示值误差测量结果的不确定度分析，表明了用TWIN-CHECK1200测长机进行校准的可行性。

This paper emphasized on the effect of the displacement of the wire from the core center and the effect of the rotation of the core, two shapes of commonly used N-turn coils were analyzed, the detailed steps for the uncertainty evaluation of clamp ammeters were given finally.

本文分别从被测导体偏心度和倾斜度以及不同校验线圈对钳形表铁心磁感应强度的影响等几方面进行分析，并给出钳形电流表校准不确定度评定的具体方法与步骤。

The method of automatic collimation of multispectral and multibeam axes—infrared,TV and lase axes is introduced in this paper.

分析了具有红外、电视和激光的光电仪器进行多光谱多光轴自动校准的方法。

An Optical Microscopy and Image Analysis method was used to certify our Monodisperse Standards against a NIST calibrated stage micrometer.

光学显微镜和图像分析方法过去常常根据 NIST 微米校准方法来证明我们的单分散标准颗粒。

This paper gives several methods to validate these new methods by analyzing images of stage micrometer, metallurgical sample, and images that consisting of definite area in geometric graph, Several kinds of validation methods including of traceability of a quantity value, printing microstucture graph, comparing microstucture photo with standard photos, length meansurement, and area meansurement are discussed in this paper.

通过分析显微镜刻度尺图像、金相样品图像，及给定特定图形且已知面积的图像，依据ISO/IEC 17025检测和校准实验室能力的通用要求，并结合金相检验标准，阐述了金相显微镜利用新方法的方法确认，其中包括量值溯源、金相组织输出、图谱比较、长度类测量和面积类测量的确认方法。

Chrysanthemum of 10 thousand birthday is lax to edaphic requirement, with the arenaceous qualitative loam with fecund, good drainage had better.

万寿菊对土壤要求不严，以肥沃。排水良好的砂质壤土为好。

He unstepped the mast and furled the sail and tied it.

他拔下桅杆，把帆卷起，系住。