上光

If the paper absorbent is too strong, it can easily lead to finish and handlethe "."

如果纸张的吸收性太强，就容易引起上光油"下沉"。

Therefore, glazing products business card printing and membership card making ink advised the dibenzylidene resistance, solvents and acidproof alkalescence.

所以，上光产品的制卡和会员卡制作油墨应选用耐醇类、酯类溶剂和耐酸碱性的。

Therefore, glazing products business card printing and membership card making ink should be chosen on the acidproof class, solvents and acidproof alkalescence.

所以，上光产品的制卡和会员卡制作油墨应选用耐酸类、酯类溶剂和耐酸碱性的。

Barelegged children on the beach.

海滩上光着腿的小孩。

Depending on the Polish tabll viscometric vary, such as the common three-roll, and carry it tooth polishing machine viscosity is 30 ~ 40s.

粘度。根据不同上光机型选用不同的粘度，如普通三辊、叼牙上光机粘度为30~40s。

On the essence of optical coating process is on the business card printing and membership card making products surface leveling and drying process.

上光涂布过程的实质，是上光涂料在制卡和会员卡制作品表面流平并干燥的过程。

Produce light oil film spray conditions normally finish normally does not produce a spray, such as user surface in cigarette packages are often in a layer on the surface of another polyolefin film, humidity and temperature in particular to certain conditions, when oil coating, the surface oil often very short gasficatic cause light fastness oil attachthemselves badnessand and above on the surface of polyolefin film appears with uniform small steam fog, in which case the contrary result in reducing or andgrainy of the goods.

产生光油薄膜雾化条件正常情况下，上光油一般不会产生雾化，例如用户在香烟盒表面往往在表面再覆一层聚烯烃薄膜后，湿度大、特别是气温高到一定条件时，当底油涂布后，面油往往因极短暂的气雾致使光油附着牢度不好，而覆在上光油表面的聚烯烃薄膜就会出现浓浓的均匀的雾状小蒸汽，这时反而降低或导致商品的肉质的变化。

Glazing system of varnish coating can be defined by liquid tuhung roll rotation and tuhung roll and measurement of the roller (also called relying solely on the roll) pressure size.

双辊式上光系统对上光油涂布量的控制，是通过液斗辊的旋转速度以及液斗辊与计量辊之间的压力大小来调节的。

In Polish, coating on the easily from high smoothness of self-leveling paper surface.

在上光涂布中，上光涂料容易在高平滑度的纸张表面流平。

The solution is to adopt a business card printing and membership card making machine instead of rubber blanket resin version, and then set the port-side seam is intended to be bonded in place rubber blanket a strip, strip of this blanket can't let paerboard, this is really looking edges, port-break light, gelatinize bond strength greatly improved after, but also to reduce the use of the cost of printing.

解决的办法是，采用一块制卡和会员卡制作机的橡皮布代替树脂版，然后将药盒边缝拟粘合的部分在橡皮布相应位置揭掉一层，使揭掉的这层橡皮布不能让纸板上光，这个办法果真见效，药盒边缝不会上光，涂胶后粘结强度大大提高，而且还降低了用树脂版制版的成本，一举两得。

In this paper, the requirement analysis, design and implementation of the system are introduced in detail.

此论文详细介绍了系统的需求分析，系统设计和具体实现。

In the context of economic globalization is increasingly deepening, China's economy can not be spared.

在经济全球化日益加深的背景下，中国经济不可能做到独善其身。