查询词典 working papers

When mine pit tunneling tunnel, breathes the fresh air for the supplies staff, the noxious gas which the dilution tunneling working surface's gas and produces, the mine dust, the creation good working condition, must carry on to the tunneling working surface ventilates.

以下为资料的部分内容，如需要全部资料请点击获取全文论文编号：JX469 有设计图，论文字数：16437，页数：61在矿井掘进巷道时，为了供给工作人员呼吸新鲜空气，稀释掘进工作面的瓦斯及产生的有害气体，矿尘，创造良好工作条件，必须对掘进工作面进行通风。

When mine pit tunneling tunnel,breathes the fresh air for the supplies staff,the noxious gas w你好ch the dilution tunneling working surface''s gas and produces,the mine dust,the creation good working condition,must carry on to the tunneling working surface ventilates.

论文编号：JX469有设计图，论文字数：16437，页数：61摘要在矿井掘进巷道时，为了供给工作人员呼吸新鲜空气，稀释掘进工作面的瓦斯及产生的有害气体，矿尘，创造良好工作条件，必须对掘进工作面举行透风。

National implementation of Article thirty-sixth day laborers working hours not more than eight hours, the average weekly working time is not more than 44 hours of the working hours system.

D|e$^，a i1第三十六条国家实行劳动者每日工作时间不超过八小时、平均每周工作时间不超过四十四小时的工时制度。

Introduction:Electroforming is such a process that working plate is got from copying master plate by galvanization in tank liquor; die pressing is another process that working plate is firstly wrapped onto the plate roller of die press, then the hologram effect of the working plate will be copied to base material of PET film or paper by heating and pressure.

概 况：电铸是以母版为载体在槽液中通过电镀工艺复制成工作版，模压是将工作版包在模压机版辊上，再以聚脂膜或纸张为基材通过加温加压方式，使工作版上的镭射激光效果复制到基材上的一种工艺。

The lift course of hanging device on wheat no-tillage planter was simulated by using the software of ADAMS. Some important parameters were obtained such as height of the working part relative to ground, the distance between the working part and the rear wheel of tractor, the angle of road pass and the force of hanging point, etc. The key parameters of the hanging device and its best working parameter of hanging device were found out through optimization simulation. Simulation results showed that suspension point had minimum force when variable DV_1 and DV_2 gained corresponding maximum and minimum at scope of structure limit.

应用ADAMS软件对小麦免耕播种机悬挂机构提升过程进行了动态仿真，得到了工作部件的位置高度、工作部件与拖拉机后轮之间的间距、路面通过角以及悬挂点的受力等参数，找到了悬挂机构的关键参数，通过优化仿真，得到了悬挂机构的最佳工作参数，仿真结果表明，设计变量DV_2、DV_3在结构受限范围内分别取其最大值和最小值，悬挂机构悬挂点受力最小。

It was shown that coal seam floor failure depth of working face 2121 was 32.5 to 5 m, approximately three times as deep as that of shallow working face(in genera l,9.15 to 12.0 m). Coal seam floor failure depth increased with mining depth. Potential risk of water inrush through coal seam floor of working face 2121 is much higher for deep mining than for shallow mining.

试验结果表明：该工作面底板破坏深度为32.5~35 m，比300 m采深以内的工作面实测深度(9.15~ 12.0 m)增加2倍以上，说明随着开采深度的增加，煤层底板采动破坏深度呈明显增大的趋势，因此，在水压和破坏深度二者同时增加的条件下，2121工作面深部煤层开采的突水危险性远远大于浅部煤层。

According to the state of the working coal seam where the working-face 706 of Xiaonan Mine exists and the characteristics of present routine technical measures taken to prevent and father the spontaneous combustion, the theory of fuzzy comprehensive appraisal is applied to analyze the plan about fire-protection technique for the working-face 706 of Xiaonan Mine.

根据晓南矿706工作面开采煤层的情况及目前常规的防治自燃技术措施的特点，运用运用模糊综合评判理论，对该工作面开采进行自燃防治方案进行的分析，综合考虑影响防火的各种因素，给出了一种新颖、简单、科学评价方法，提出了该工作面防火技术的最佳方案，取得了理想的防治效果。

Besides the letters, I've also drawn a vertical line on both papers.

除了信件，我也得出一条垂直线，两文件。

An alternative source for many of the same papers, together with a useful abridgement of Kaplan's classic, Demonstratives.

同类论文的可选读本，包含 Kaplan 的经典著作《指示》的有用删节本。

Then he went absent-mindedly through the pile of papers on his desk, writing in his occasional notes: Go to Spain?

然后他心不在焉地翻阅了书桌上一堆书信文件，在他零星的日记里写道："到西班牙去？"

I want to be a big fish in a small pond.

我要做一条在小池塘里的大鱼。

While the software functioned well, we did not feel the same about their customer support!

虽然该软件运行良好，我们没有同样的感觉他们的客户支持！