查询词典 variable speed

By establishing the mathematical model of the variable displacement pump variable displacement motor volume speed-modulating system and dynamic simulation with the module of MATLAB/SIMULINK,analyzed and concluded the dynamic characters and impact factors,offer a theoretical basis for further application.

通过对变量泵-变量马达容积调速系统进行数学建模和利用MATLAB/SIMULINK模块进行的动态仿真，分析和总结了容积调速系统的动态特性及其影响因素，为以后的系统应用提供了理论依据。

The three-phased half-controlled bridge commutation and stabilizing voltage adjuster of permanent-magnet generator , which is also a rectifier, wastes a little electricity power and outputs high efficiency , makes it generate stable direct circuit, solves vehicle's problem of generating stable voltage at variable speed and variable load.

永磁发电机三相半控桥式整流稳压器集稳压、整流于一体，电能消耗少，发电效率高，输出直流电压稳定，解决了汽车用永磁发电机在变转速、变负载工况下输出电压保持稳定的问题。

The variable spraying control system took the S3C44B0X microprocessor of ARM7 series as its core control part and programmed with C language in the UCOS-Ⅱ environment. The system was able to fulfill the data acquisition and processing of the position and the speed about the sprayer, the pressure and the flow about nozzles, and recognize the plot and then adjust the electrical control valve to realize variable spraying.

该系统以ARM7系列的S3C44B0X微处理器为核心，在UCOS-Ⅱ操作系统环境下，使用C语言编程实现机具作业位置、行进速度、喷头入口压力以及喷头喷药量信息的采集与处理、网格识别和电动调节阀控制。

Based on the research on the theory and technology of dual-PWM variable frequency AC motor control, a design of dual-PWM variable frequency AC motor control system which has factor control loop rectifier and slip frequency speed regulator is proposed.

本文在总结和研究当前双PWM变频调速基础理论和常见技术的基础上，设计并研究了一种基于DSP的整流侧功率因数闭环、逆变侧转差频率控制的双PWM异步电机变频调速系统。

During the starting and lowspeed range, the stator windings are shortcircuited and the DFIM system is operated in variable frequency drive mode supplied by rotor side; in highspeed range, the motor works in doublyfed mode, so wide variable speed range can be achieved.

该系统在起动和低速段将定子绕组短路，转子侧采用变频调速运行方式，在中高速段则采用双馈调速运行方式，从而实现了双馈系统在宽转速范围内的平滑调速。

The results show that the zero speed point is located on the arc between two absolute speed zero points of rotation axes, and the necessity of relative speed zero point is demonstrated, From the location of speed zero point, some useful conclusions can be drawn.

对速度零点的位置进行了分析，得出了如下结论：对于一定形状的工件，通过调整两轴的转速比以及两轴夹角参数，可以将速度零点置于工件之外，从而避免速度零点对研磨的不利影响。

With the help of computer program, zero speed point was searched. The results show that the zero speed point is located on the arc between two absolute speed zero points of rotation axes, and the necessity of relative speed zero point is demonstrated.

利用程序对相对速度零点的位置进行搜索，发现速度零点处于两轴绝对速度零点之间的圆弧上，从而证明了相对速度零点存在的必然性。

Take advantage of the high-speed calculation capability of DSP. Without any additional speed-measuring circuit,calculating the running speed.,then modulating PWM can be easily made to control the speed of the motor.

充分利用DSP高速的运算能力，在不需要另加测速电路的情况下，软件计算电机的在转速度，然后根据在转速度，调节PWM波的占空比，很方便实现电机的调速，达到电机无传感器的控制。

Plastic should lower 3 steps, because plastic is a step to add melt resin material to cyclinder , Higher stick of resin material ,higher screw back pressure. Screw speed differs depending on decomposing temperature of resin material ,Higher screw speed ,Higher trim force of resin, higher cyclinder temperature. Some resin material may decomposes so it set screw speed in mid-speed such as 45-75%, In plastic step setting screw back pressure is very important, Higher screw back pressure ,higher quality of product screw back pressure make resin structure order, Molding product is beautiful and volume stable.

再复杂的熔胶旋转过程最多不会超过三段，因为熔胶本身就是存在于把胶熔进料筒的过程，如果原料粘度大，熔胶压力则大，但速度则应取决于原料的分解温度，熔胶速度越快，原料中的剪切力则会越大，料管温度则越高，局部原料产生分解的可能性则会越大，故一般熔胶会采用中速为宜，如45%-75%，熔胶同时会碰到一个比较重要的环节，那就是背压的使用，产品精度要求越大，背压的使用则更大，背压可使原料分子间结构更紧密，成型出的产品则尺寸更稳定，外观越好。

Plastic should lower 3 steps, because plastic is a step to add melt resin material to cylinder , Higher stick of resin material ,higher screw back pressure. Screw speed differs depending on decomposing temperature of resin material ,Higher screw speed ,Higher trim force of resin, higher cyclinder temperature. Some resin material may decomposes so it set screw speed in mid-speed such as 45-75%, In plastic step setting screw back pressure is very important, Higher screw back pressure ,higher quality of product screw back pressure make resin structure order, Molding product is beautiful and volume stable.

再复杂的熔胶旋转过程最多不会超过三段，因为熔胶本身就是存在于把胶熔进料筒的过程，如果原料粘度大，熔胶压力则大，但速度则应取决于原料的分解温度，熔胶速度越快，原料中的剪切力则会越大，料管温度则越高，局部原料产生分解的可能性则会越大，故一般熔胶会采用中速为宜，如45%-75%，熔胶同时会碰到一个比较重要的环节，那就是背压的使用，产品精度要求越大，背压的使用则更大，背压可使原料分子间结构更紧密，成型出的产品则尺寸更稳定，外观越好。

Some of them were ligated to the plasmid vector pCR 2.1 andsequenced,respectively.

将所获DNA片段克隆到pCR2.1载体进行测序，并与基因组数据库进行同源性比较。

Thinking since Google owns Blogger, I would be able to escalate this issue to the support team.

自谷歌的思考拥有Blogger的，我将能够缓解这一问题的支持团队。