查询词典 under correction

Correction of severe congenital blepharoptosis by suspension of frontal muscle flap overlapped with orbital septum aponeurosis flap

采用带血管蒂的额肌帽状腱膜复合组织瓣Ⅰ期修复重建了17例前颅底中线区大面积洞穿性组织缺损。

Put forward is a new method of skin effect correction based on function relationship between the real part of apparent conductivity against frequency and true formation conductivity in uniform formation condition.

根据均匀地层感应测井视电导率实部与频率和地层电导率的函数关系提出了一种双频率校正与归一化校正相结合的趋肤效应校正新方法。

The approximate formula of the damper deployment time was deduced by time correction factors.

用时间修正系数的概念推导了阻力器展开时刻的近似计算公式。

The polynomial approximation method is also employed to obtain simple formulas for frequency and amplitude correction.

本文利用多项式逼近方法获得了频率和幅值修正的计算公式。

The experimental results show that in both the learning speed and correction of character recognition, the Levenberg-Marquardt Back-Propagation Neural Networks in recognition of the capital English characters and the Arabic numbers is the best approach.

从实验结果得知，无论是学习速率或字元判别的正确率，都是Levenberg-Marquardt倒传递类神经网路在辨识英数字元影像上为最佳。

Correctional checking formula of melt flow ratio in injection molding was obtained by introducing a correction coefficient β which reflected the complexity degree of mold cavity. The results show that, the maximum flow ratio of 486 can be obtained when injection pressure ranges from 150 MPa to 160 MPa in Archimedes spiral mold for PP, while maximum flow ratio of 419 can be obtained when injection pressure ranges from 160 MPa to 170 MPa for PE. There is a local fluctuation phenomenon for flow ratio and corresponding injection rate in square spiral mold when injection pressure of 100, 120 and 150 MPa for PP and 130, 140 MPa for PE are reached respectively,and this phenomenon is more serious for good fluidity of melt. The average flow ratio in Archimedes spiral mold is 6% larger than that in square spiral mold for PP, and 4% for PE, the average flow ratio of PP is 19% bigger than PE in Archimedes spiral mold, and 15% in square spiral mold. The influence of the cavity profiles on the melt flow ratio is more significant for good fluidity of melt.

研究结果表明：在阿基米德螺旋线模具中，PP在注射压力为150~160 MPa时取得最大流动比485，PE在注射压力为160~170 MPa时取得最大流动比419；在方形螺旋线模具中，PP在注射压力为100，120和150 MPa，PE在注射压力为130和140 MPa时流动比及所对应的注射速率出现波动，且流动性好的熔体波动更为严重；PP在阿基米德螺旋线模具中的流动比均值较其在方形螺旋线模具中大6%，而PE大4%；在阿基米德螺旋线模具中流动比均值PP比PE的流动比均值大19%，而在方形螺旋线模具中PP的流动比均值比PE的大15%；流动性好的熔体受模具型腔轮廓特征影响大。

The correction factor of normal stress graph area to rationalize reinforcement design is also studied.

通过对桂江巴江口水电站溢流坝弹性有限元计算成果的分析，指出部分结构仅根据主拉应力图形面积进行配筋存在的问题，并给出正应力图形面积的修正系数，使配筋结果更加合理。

The method of area ratio,the area of a circle in sample plot to the whole area of the circle, in which the distributing point is the center and the scale distance is the radius,is defined as the weighted coefficient of edge correction in this paper.

将边缘效应的权重值定义为以分布点为圆心，尺度距离为半径作圆，圆在样地内的面积部分与整个圆面积之比。

Based on currentarrestmentexecutive status of China,this paper analyzes the root cause of that status of arrestment on its theory,legislation and judicatory.The attitude to arrestment needs correction urgently.It should be claimed that hum an right protection is the true target instead of fighting crime is.Clarifying purpose of arrestment can reduce its improper use.

立足中国逮捕实践的现状，本文从理论、立法和司法三个方面深入剖析了其中的原因之后，认为当前的逮捕价值观急需纠偏，呼吁以"人权保障"替代"打击犯罪"作为逮捕的首要价值，以期减少对逮捕的不当适用。

Based on currentarrestmentutive status of China,this paper analyzes the root cause of that status of arrestment on its theory,legislation and judicatory.The attitude to arrestment needs correction urgently.It should be claimed that hum an right protection is the true target instead of fighting crime is.Clarifying purpose of arrestment can reduce its improper use.

立足中国逮捕实践的现状，本文从理论、立法和司法三个方面深入剖析了其中的原因之后，认为当前的逮捕价值观急需纠偏，呼吁以"人权保障"替代"打击犯罪"作为逮捕的首要价值，以期减少对逮捕的不当适用。

In the chapter 2, the theoretic knowledge about the photosensitive resin and the grinding tools was firstly introduced.

第二章阐述了光固化树脂结合剂磨具的相关理论研究。

Do not use the program's indenting or margin-setting features; these will be added during typesetting.

不要使用缩排，页面边缘设置之类的选项，偶看不大懂。