查询词典 trial-and-error method

Taking the design of plane mechanism as an example, the paper briefly explains how to apply the snap function of AutoCAD to graphology, analyzes the design error of graphic method,and discusses about the error control of the method.

以平面机构设计为例，简要说明如何将AutoCAD的各种捕捉功能用于图解法中，并对其设计误差进行了分析，对误差控制进行了探讨。

The method how to separate the radial jumpiness of the large shaft by three-point method to gain the round error in high precision is showed particularly. In the part of diameter measurement, this paper indicates how to standardize the photomicrosensor and shows the way how to use correction signal correct the measure error of the grating system which is used to measure the rotated angle of the wheel in detail.

文中详细论述了在圆度误差测量中，利用三点法分离大轴支承径向跳动引起的测量误差而获得高精度的圆度误差测量值的方法以及直径测量系统中，光电开关测量精度的标定方法和通过构建误差修正函数对实现滚轮转角测量的圆光栅系统的测量误差进行实时修正的方法。

this paper analyzed the error of two methods of printer fuzzy identification by a case of laser printer identification. by error analysis of single method and united method, it evaluated the reliability of two methods about printer identification.

摘 要：通过实际案例的激光打印机打印文字，鉴别打印机型和打印机墨粉类型，分析打印文字图像或墨料ftir图形单一鉴别与联合鉴别结果之间的误差率，评估两种鉴别方式的可靠性差异。

Furthermore, how to apply the model efficiently in practice is deeply discussed. As the variance produced by the forecasting model as concerned, the real-time revised method of hydrological forecasting is highlighted. Next arranged, the multi-stratum recursive prediction model is put forward to forecast the error series that is a dynamic system. Later, an error selfregressive multi-stratum recursive prediction model is set up as well as a current algorithm offered. Finally, the difference collated model and the gloss control method, which are devoted to updating the mid-long term hydrological forecasting during the meditate period, are put forward.

在综合评述中长期水文预报现有方法和模型的基础上，采用时间序列分析方法，建立中长期水文预报的时间序列组合模型，并对模型如何在实际中有效应用作了较为深入的探讨；针对模型预报所产生的误差，又重点研究了水文预报实时修正方法：提出了采用多层递阶预报方法对误差序列这一动态系统进行预报，建立了误差自回归多层递阶预报模型，并提出了较为通用的解算方法；给出了水文中长期预报中期修正的残差相关模型和总量控制方法。

The cylindricity could be calculated by least squares method and wavelet error separation method that the measurement error could be decomposed by Harmonic analysis algorithm based on wavelet theory.

针对激光 CCD 灵敏度高，干扰噪声容易混入测量数据中的问题，提出了一种基于小波分析的误差分离方法，即运用谐波分析的思想方法和小波理论中多频率分析算法进行误差分离，误差分离后的数据用最小二乘法处理求出圆柱度。

During the process of camshaft measurement, the phase datum of the key pin or the locating pin can be determined precisely by using the minimum error method of curve symmetry and the cam nose position can be determined by using the minimum error method near the" sensitive point".

在凸轮测量中，采用曲线对称最小误差法，可精确确定键销或定位销的相位基准；采用&敏感点&附近最小误差法，可精确确定凸轮&桃尖&位置。

The results show that the error of considering the curve of strand as line is less than 2%, through the comparison with the result of FEA and experimental data, the error of principal tensile stress is less than 0.2 MPa, which prove that the precision of the method meets engineering calculation requirement, the method is feasible.

理论分析结果显示，将预应力束的平弯曲线用直线代替产生的误差不超过2%，该公式计算结果与有限元结果及实测数据比较表明，主拉应力的计算误差小于0.2 MPa，结果满足工程精度需要，该方法可行。

The analysis procedure,classifi-cation of measurement error,calculating of radom uncertainty,bias limitsof systematic error and total uncertainty for this method are emphasised.The problems of future research for this method are investigated.

着重介绍这种方法的分析步骤、误差的分类、随机不确定度、系统误差限和总不确定度的计算方法，同时还探讨了这种方法尚待进一步研究的问题。

To reduce the large numerical dispersion error for the alternating direction implicit finite-difference time-domain method, an isotropic ADI-FDTD method with low numerical dispersion error was presented.

针对交替方向隐式时域有限差分方法数值色散严重的缺点，提出了一种低数值色散的各向同性ADI-FDTD方法。

As to system＇s uncertainty such as time varying characteristics, grey multiple step error correction method took the place of the conventional single step error correction method.

针对对象特性时变等不确定因素，该文以灰色多步误差预测校正替代原有算法的当前一步误差校正，可以更为有效的克服模型失配等因素的影响。

It's not quite as simple as that.

并没有那么容易。

It debuted in 1992 in Japan and the United Kingdom, and 1993 in the United States.

它首次亮相于1992年在日本和英国，在美国1993年。