查询词典 stabber

They also like when I stabber cone, and sometimes like a wound-shih spew black or medicine.

它们又时像锥子锥我，有时像敷在伤口上的白霜或黑药。

He is a back stabber .

他是个会在背后捅你一刀的人。

Back stabber I've heard that Greedie Corporation is a terrible place to work , because the company is filled with back stabbers and liars .

我听说在格利迪公司工作简直让人无法忍受，因为公司里的人不是背后说别人的坏话，就是说谎。

He's a double talker. 13.He's a back stabber.

他见人说人话，见鬼说鬼话。

In order to fight with this sleepiness, he even went to extremes, stabbing his thigh with an stabber every time when he began to be sleepy.

由于他常常挑灯夜读，有时困乏得睁不开双眼，所以为了战胜疲劳，他竟然使用一种极端的办法，只要一打瞌睡。

That person then picked up a stabber, do what makes the elephant, the elephant jumped into a pool of love.

那人这时拿起一个锥子，扎了大象屁股一下，大象疼的跳进了游泳池。

Jab , prod , poke , dig stabber n .

刺的东西，锥子，暗杀者

Pass to count to Wisterch parameter , and the steel wire is different from the molding tool get in touch with the length, and settle the path the research taking the length work the stabber angle to get under differently pull to stir the term, mold core adoption of best severally why size, combine the best work stabber of research the Cape, and settle the path to take the length nextly steel wire is in the molding tool of have fever to measure, air inside dispel-heat calories, winding dispel-heat on the coil-canister , and its molding tool dispel-heat calories of, and cause the steel wire the temperature difference pass in and outing the molding tool to influence steel wire machine function, under the experiment inside pull to stir the term according to the same race different work stabber Cape half of adoption the Cape(7 degree,10 degree,12 degrees, the best mold Cape, experience mold Cape) settle the path to take the length(2-3 mm,3-4 mm,4-5 mms, theories length, experience length) to proceed to experiment, and get the conclusion, work stabber the Cape then is more big the steel wire get in touch with the length with

通过对Wisterch参数，钢丝与模具接触长度、定径带长度、工作锥角度的研究得到了在不同拉拨条件下模芯采用的最佳几何尺寸，并研究最佳工作锥角、定径带长度下钢丝在模具中的发热量、空气中散热量、卷筒上的散热量及其模具散热量的不同，导致钢丝进出模具的温度差别对钢丝机械性能的影响，在实验中根据同种拉拨条件下采用不同工作锥角半角、定径带长度进行试验，得出结论，工作锥角越大则钢丝与模具接触长度越短，钢丝变形越剧烈，在模具中发热量就越高，导致钢丝出模温度高，使钢丝强度、硬度升高，弯曲、扭转次数降低，并且降低模具使用寿命。在其它条件相同的情况下，定径带越长则钢丝与定径带简壁磨擦增大，使钢丝发热量加大，从而使钢丝强度、硬度略升高，弯曲扭转次数略降低但定径带的增大减小了钢丝变形产生的弹性后效使钢丝出模直径比较稳定。

He taunts. So the granny-stabber dispatches five dirties to deal with him.

他嘲笑道。于是这个老妇杀手又派了五个肮脏的家伙去对付他。

It is also known as one of the most poisonous naturally occurring substances.

它也被称为一个最自然发生的有毒物质。

The greatest stress is found at the location on the cross section where V is the largest.

最大应力出现在横截面上V为最大的地方。