查询词典 spring beam

YM-tensioned anchor client 1, YM strand tensioned anchor client system includes: YM15 anchor (for §15.2,§15.7mm strand) YM13 anchor (for §12.7,§12.9mm Steel Stranded) BM15, BM13-type flat anchor YMZ15, YMZ13-ring anchors (applied to the structure of cyclic stress) 2, YML Series connectors include: single as used prestressing tendon lengthening, usually with in pre-tensioned law; porous as the next long prestressed beam, normally used in the continuous beam. 3, P-type anchorage system for P-type anchorage system includes extrusion anchor (from compression set and a triangle composed of copper wire extrusion spring), anchor anchor plate, spiral reinforcement, constraint circle bellows.

YM张拉端锚具1、YM钢绞线张拉端锚固体系包括：YM15锚具（适用于ф15.2、ф15.7mm钢绞线）YM13锚具（适用于ф12.7、ф12.9mm钢绞线）BM15、BM13型扁锚YMZ15 、YMZ13 型环锚2、YML型系列连接器包括：单孔作为接长预应力筋用，通常用于先张法中；多孔作为接长预应力束，通常用于连续梁中。3、P型锚固体系P型锚固体系包括挤压锚具（由挤压套和三角形铜丝挤压簧组成）、锚固锚板、螺旋筋、约束圈、波纹管。

This paper carried out nonlinear finite element analysis of Reinforced concrete two-way thin-slab of frame construction, which received uniformly distributed load and four sides supported with spring beam in the normal stage.

本文对正常使用状态下，框架结构中承受均布荷载的，周边为弹性支撑梁的钢筋混凝土双向薄板进行了非线性有限元分析。

Based on the results of experimentation and field test as well as the properties of time-dependent structural system, a model of the continuous beam with spring supports for simulating the high-rise concrete building during construction was proposed.

根据室内试验和现场实测的结果，结合施工时变结构的受力特点，针对梁板柱体系混凝土结构，本文建立了施工时变结构体系分析的弹性支撑连续梁模型CBSS(Continuous Beam With Spring Supports)，提出了基于弹性支撑连续梁模型CBSS的高层建筑混凝土结构施工过程受力性能的仿真分析方法。

The frequency characteristics of this system are related to two ratios: the ratio of the beam and rigid hub inertia J＇, the ratio of the torsional spring and beam bending stiffness K＇.

实验和理论分析均表明，刚柔惯量比J＇和刚柔刚度比K＇对系统的频率有着重要的影响。

Reasonable baseline is one of the key matter in the straightness measurement. Two schemes of the measuring basis are advanced in the paper--tensile spring and laser beam, based on the request and character of guide-ways straightness measurement. In early study, we come to the conclusion by theoretical analysis and experiment that the laser beam basis has more advantage in development and accuracy.

合理的直线基准是实现直线度测量的一项关键内容，本文首先针对导轨直线度的测量要求与特点，提出了张丝与准直激光束两个测量基准方案，并在前期研究中通过理论分析与大量的实验对比得出结论：激光束在系统实现及测量精度等方面均具有更高的优越性。

Following the simple formula of the spring coefficient of a beam and the exact formula of the capacitor for the switch,the quasi-static and dynamic pull-in voltages of the clamped-clamped beam switch on CPW are analyzed,and the damping effect is also included.

通过简化的弹性系数和精确的电容计算公式，详细分析了基于CPW的双端固支梁开关的准静态和动态吸合电压。

Finite element model of light-weight steel-concrete composite beams are built up. This element model combines spring element with traditional beam element to form a composite beam element which consists of steel, concrete and springs. The three parts has compatibility of deformation.

2建立了轻钢-混凝土组合梁的非线性有限元分析模型，该模型由传统的梁单元中加入弹簧单元，由钢梁部分、混凝土部分和弹簧三部分在变形协调的基础上组成一个复合梁单元。

In order to ensure sensitivity and precision of transducer of spring beam,according to "stress concentration" design philosophy,based on reasonable choice of transducer,its strain and strength are calculated using FEM,the paster place of spring beam should be ascertained in reason,and the transducer's maximum strain orientation and measuring range are determined theoretically.

采用弹性梁对旧式液压万能材料试验机下横梁进行改造，为确保弹性梁传感器的灵敏度和精度，根据应用"应力集中"的设计原则，在合理选择传感器结构基础上，采用有限元法对其应变和强度进行计算，合理确定弹性梁的贴片部位，从理论上确定传感器的最大应变方位及传感器的量程。

Different from the two-leaf-spring structure in the market right now, we applied one-leaf-spring as the suspension system. One design is the leaf spring of single cantilever beam and the other is the leaf spring of double cantilever beams.

有别於一般市面双弹片架构，本文使用单弹片作为悬吊系统，一款为单悬臂梁连结镜座；另一款为双悬臂梁连结镜座。

The vertical torsion spring laser guide beam arm is designed by analytic method, and the load curve is mapmaked in the permited fluctuation range. A torsion spring curve is designed to match with the VTSLGBA′s feature curve, and the torsion spring design parameter can be confirmed according to the match result.

采用解析法优化设计了立式扭簧激光导光臂，在允许的工作波动范围内绘出导光臂的载荷曲线，然后设计出一条扭簧的扭矩曲线使其与导光臂的载荷曲线相匹配，再根据匹配结果确定扭簧的设计参数。

It is also known as one of the most poisonous naturally occurring substances.

它也被称为一个最自然发生的有毒物质。

The greatest stress is found at the location on the cross section where V is the largest.

最大应力出现在横截面上V为最大的地方。