查询词典 speed up

At present, there are drilling more than 150 plants, with an annual output of various drilling about 1 million units, export over 20 million units, the drilling of speed through a pulley shift to resolve the pagoda, the governor need to stop the process, open the protective Enclosures, manual transmission, and other procedures, the process cumbersome and poor security, and is governing, not transferred to the spindle speed corresponding to the different materials of various aperture drilling at the best speed, the production efficiency is low.

目前，全国有钻床厂150多家，年产各种钻床100万台左右，出口20多万台，这些钻床的变速都是通过一对宝塔皮带轮换档解决的，调速过程需要停车、打开防护罩，手工换档等程序，操作过程繁琐且安全性差，并且是有级调速，不易使主轴转速调到对应于不同材质的各种孔径钻削时的最佳转速，因此生产效率也低。

The economy and performance characteristics of LIYANG car equipped with CVT and MT are studied respectively and compared. 3Based on experimental analysis, the relation among the speed ratio changing rate, oil pressure of driving and driven pulley cylinders, driving pulley input speed and torque, metal belt speed ratio has been studied. Model for getting the ratio changing rate is put forward, and practical equation giving the ratio changing rate is obtained by experiments.

对装有CVT和装有MT的羚羊轿车的经济性和动力性进行了计算和比较分析。3）通过实验分析，研究了主、从动轮油缸压力、主动轮转速、输入转矩和带式无级变速传动速比与速比变化率的关系，建立了获取CVT速比变化率的模型，导出了符合实际规律的实用计算公式。4）应用键合图理论，建立了金属带式无级变速汽车传动系的键合图模型，推导了系统的状态方程。

Cutting experiments in tools factory show that the lathe tools and milling cutters made of the modified cast high speed steel can achieve the qualified standards for wrought high speed steel tools according to the Chinese National Standards, and the useful life of the modified cast high speed steel lathe tools is increased three times longer than that of the forged lathe tools.

变质M2铸造高速钢车刀和立铣刀在工厂的切削实验与应用表明：这两种刀具均达到国家规定的锻造高速钢刀具合格品标准，且车刀的耐用度较锻造车刀提高3倍以上。

At same time, designed software and hardware systems collecting and processing flywheel transient speed of the engine, measured flywheel transient speed fluctuation and indicator diagram of engine under different speed and different load, and testified the effectiveness and reliability of the constructed models.

相应地设计了发动机飞轮瞬态转速采集与处理软、硬件系统，并实测了各种工况下发动机飞轮瞬态转速波动及示功图，验证了所建模型的有效性和可靠性。

The instrument change speed of revolution to impulse signal by photoelectric transducer and as input signal of 8031 uniwafer-computer, then count input signal of revolution speed impulse through Time/Counter of 8031, thus revolution speed was measured.

此电压测量装置利用光电式传感器把转速信号转换为脉冲信号，作为输入信号通过8031单片机的定时器/计数器对输入的转速脉冲信号进行计数，来测量转速。

The purpose of a motor speed controller is to take a signal representing the demanded speed, and to drive a motor at that speed.

马达速度控制的目的，是要代表一个信号要求的速度，并在该驱动马达的速度。

Increase Speed - If the boss decides to chase you, the passenger can apply a speed boost to the vehicle allowing it to speed away (25 energy or 50% ammo).

速度提升：如果boss开始追你了，乘客可以给载具提供一个加速效果，允许载具快速离开(消耗25能量或者50%的弹药)。

When considering the speed is enough to first check whether the normal speed motor itself can be used to measure the tachometer, the motor speed under normal circumstances, consider whether there will be magnetic coupling of the slip.

在考虑转速是否够时，先要检查电机本身的转速是否正常，可用转速计进行测量，在电机转速正常的情况下，可考虑是否会出现磁力联轴器的滑脱。

This paper aims at the design, implementation and evaluation of an industrial brushless servomotor drive. The proportional-plus-integral speed control with gains tuned by an extension of the frequency-zone method and anti-windup PI speed control based on self-conditioning techniques are studied. The parameters of speed performance criteria, control loop bandwidth, per normal inertia, and noise sensitivity are employed to evaluate the performance of the drive.

本文针对工业用无刷伺服马达驱动器进行设计与制作，延伸频率区域法分别设计比例积分控制之增益值，以自我条件技术完成比例积分速度控制之反卷起设计，并依据速度性能准则之参数，如控制回路频宽、惯量标么值、杂讯灵敏度等，进行驱动器之性能评估。

Machine drive principle: No matter it is mono-block type or detached type, we take electromotor as original motor to convey the power to retarder input shaft (high-speed rotation axle) through direct connection or triangular belt and retarder output shaft (low-speed rotation shaft) connects directly with the joint screw or low-speed rotation shaft connects with the main shaft joint screw through coupling thrust bearing socket.

机械传动原理：本司产品无论是整体式的还是分体塑料再生机，均以电动机为原动机，通过直连式或三角带将电动的力传递给减速器轮入轴由减速器输出直通联接螺杆或经低速轴通过联轴器止推轴承座主轴联接螺杆，使螺杆按设计要求及生产工艺要求的扭矩和转速匀速地旋转，以达到塑料塑化后定压、定量、均匀地连续挤出的目的。

It's not quite as simple as that.

并没有那么容易。

It debuted in 1992 in Japan and the United Kingdom, and 1993 in the United States.

它首次亮相于1992年在日本和英国，在美国1993年。