查询词典 source material

In the light of cost index and pollution degree, the characteristics of kinds of pulp are analyzed in detail, and the GP pulp which is low cost, high-yield, no-pollution is chosen as the material of tableware. Based on material element analyzed, shaping technology is designed, the to and for single plane shaping equipment which is high shaping quality, high production efficiency and is easy to automatize is chosen. All kinds of measure are taken to solve the problems which are inequality in the shaping process of GP pulp, and dosage which matches with GP pulp is chosen. Some ways of fixing shape and heat up are analyzed, the technology of saving energy of heat pressing to fix shape being composed of oil heat and only one fixed shape in the mold is applied, with which it is high production efficiency, low cost to fix shape effectively, which saves energy 30 percent. In order to make the production line meet with material of GP pulp, measure are taken to solve the problem of pulp adhered to netlike molding which can lead to carry material difficult, the structure of fully automatic equipment is renovated, the loaded beam is optimizationally designed to make equipment structure compactand improve location precision and products quality. According to technologic flow and actual characteristic, Omron PLC is chosen as the core of the control system, proximity switch as detect unit take the place of touch switch, software is designed reasonably according to time order figure, hardware is simplified, the reliability of system is advanced, the stability of system is assured to make production order. Intelligence neuron PID system is studied theoretically which is made up of both neuron with self-organizing and self-learning function and ordinary PID with the characteristic of the simple structure and high stability, which can automatically tune the parameter with the change of system parameter, remain perfect performance.

按成本指标和污染程度分析各浆料的特点，选择低成本、高得率、无污染的磨石机械浆为原料，在原料组分分析的基础上，设计成型工艺，选择成型质量好、生产率高、易实现自动化的往复式单板成型机，采取各种措施解决GP浆成型不均匀的问题及选择与机械浆相匹配的助剂；分析几种定型方式和加热方式，采用定型效果好、生产率高、成本低的油加热与模内一次性定型相结合的热压定型节能技术，节能30％；为了使生产线适应磨石机械浆原料，采取相应措施解决由于粘网造成物料转移困难，对全自动设备结构进行改进设计，着重对物料传送系统的关键部件——承载梁的进行优化设计，使设备更加紧凑合理，提高设备的定位精度和产品质量；根据生产线工艺流程和现场特点，选用OMRON CPM1A型PLC为主核心，接近开关作为检测元件，替代有触点开关，选用可编程终端代替常规面板按扭，并按照时序图科学合理地设计软件，有效地简化系统硬件构成，提高系统的可靠性，保证系统的稳定性，从而使生产更加通畅有序；从理论上探索将神经元应具有的自组织、自学习要求与PID控制结构简单、稳定性好的全自动纸浆模塑餐具生产线的研究特点结合起来，构成神经元自适应PID控制器，当参数的变化时，系统能自行参数整定，保持优良的工作性能指标，满足实际需求。

This design develops the Firsthuida material management system ,the system will be able to achieve the company's demand, and urge the material supervisory work achieve the company standardized, the sequencing, and avoided the material management capriciousness, enhanced the speed and the accuracy of the information processing, then employee could prompt, accurate, effective inquiry and revises the material situation.

本设计所开发的第一会达公司资料管理系统正迎合了公司的需求，资料管理系统地实现将会使公司的资料管理工作更加规范化、程序化，避免资料管理的随意性，提高信息处理的速度和准确性，能够及时、准确、有效的查询和修改资料的情况。

Nation and importing metal original material of region, for example:Stainless steel(SUS301, SUS304),Carbon steel(50#, 60#, S45C, S50C, S60C, S65C, SK2, SK4, SK5, SK7), Cube(C17200), the Nie cupronickel (C7521)waits various card number, the metal book material and plank material of different material, thickness scope(0.05 mm~5.00 mm), width scope(3.00~1500 mm) and degree of hardness Class(1|4 H, 1|2 H, 3|4 H and H, EH and SH), the product quality presses the standard of Japan JIS strictly a control.

本公司主要销售日本、韩国、台湾等国家及地区的进口金属原材料，例如：不锈钢（SUS301、SUS304）、碳钢（50#、60#、S45C、S50C、S60C、S65C、SK2、SK4、SK5、SK7）、铍铜（C17200）、洋白铜（C7521）等各种牌号、不同材质、厚度范围（0.05mm ～ 3.00mm）、宽度范围（3.00 ～ 1500mm）、硬度级别（1/4H、1/2H、3/4H、H、EH、SH）之金属卷材及板材，产品质量按日本JIS标准严格控制。

Plastic should lower 3 steps, because plastic is a step to add melt resin material to cyclinder , Higher stick of resin material ,higher screw back pressure. Screw speed differs depending on decomposing temperature of resin material ,Higher screw speed ,Higher trim force of resin, higher cyclinder temperature. Some resin material may decomposes so it set screw speed in mid-speed such as 45-75%, In plastic step setting screw back pressure is very important, Higher screw back pressure ,higher quality of product screw back pressure make resin structure order, Molding product is beautiful and volume stable.

再复杂的熔胶旋转过程最多不会超过三段，因为熔胶本身就是存在于把胶熔进料筒的过程，如果原料粘度大，熔胶压力则大，但速度则应取决于原料的分解温度，熔胶速度越快，原料中的剪切力则会越大，料管温度则越高，局部原料产生分解的可能性则会越大，故一般熔胶会采用中速为宜，如45%-75%，熔胶同时会碰到一个比较重要的环节，那就是背压的使用，产品精度要求越大，背压的使用则更大，背压可使原料分子间结构更紧密，成型出的产品则尺寸更稳定，外观越好。

Plastic should lower 3 steps, because plastic is a step to add melt resin material to cylinder , Higher stick of resin material ,higher screw back pressure. Screw speed differs depending on decomposing temperature of resin material ,Higher screw speed ,Higher trim force of resin, higher cyclinder temperature. Some resin material may decomposes so it set screw speed in mid-speed such as 45-75%, In plastic step setting screw back pressure is very important, Higher screw back pressure ,higher quality of product screw back pressure make resin structure order, Molding product is beautiful and volume stable.

再复杂的熔胶旋转过程最多不会超过三段，因为熔胶本身就是存在于把胶熔进料筒的过程，如果原料粘度大，熔胶压力则大，但速度则应取决于原料的分解温度，熔胶速度越快，原料中的剪切力则会越大，料管温度则越高，局部原料产生分解的可能性则会越大，故一般熔胶会采用中速为宜，如45%-75%，熔胶同时会碰到一个比较重要的环节，那就是背压的使用，产品精度要求越大，背压的使用则更大，背压可使原料分子间结构更紧密，成型出的产品则尺寸更稳定，外观越好。

Plastic should lower 3 steps, because plastic is a step to add melt resin material to cyclinder , Higher stick of resin material ,higher screw back pressure. Screw speed differs depending on decomposing temperature of resin material ,Higher screw speed ,Higher trim force of resin, higher cyclinder temperature.Some resin material may decomposes so it set screw speed in mid-speed such as 45-75%, In plastic step setting screw back pressure is very important, Higher screw back pressure ,higher quality of product screw back pressure make resin structure order, Molding product is beautiful and volume stable. But

再复杂的熔胶旋转过程最多不会超过三段，因为熔胶本身就是存在于把胶熔进料筒的过程，如果原料粘度大，熔胶压力则大，但速度则应取决于原料的分解温度，熔胶速度越快，原料中的剪切力则会越大，料管温度则越高，局部原料产生分解的可能性则会越大，故一般熔胶会采用中速为宜，如45%-75%，熔胶同时会碰到一个比较重要的环节，那就是背压的使用，产品精度要求越大，背压的使用则更大，背压可使原料分子间结构更紧密，成型出的产品则尺寸更稳定，外观越好。

Plastic should lower 3 steps, because plastic is a step to add melt resin material to cyclinder , Higher stick of resin material ,higher screw back pressure. Screw speed differs depending on decomposing temperature of resin material ,Higher screw speed ,Higher trim force of resin, higher cyclinder temperature. Some resin material may decomposes so it set screw speed in mid-speed such as 45-75%, In plastic step setting screw back pressure is very important, Higher screw back pressure ,higher quality of product screw back pressure make resin structure order, Molding product is beautiful and volume stable. But ,it maybe flow if screw back pressure too high .

再复杂的熔胶旋转过程最多不会超过三段，因为熔胶本身就是存在于把胶熔进料筒的过程，半夜盗汗897就去播播Z如果原料粘度大，熔胶压力则大，但速度则应取决于原料的分解温度，熔胶速度越快，原料中的剪切力则会越大，料管温度则越高，局部原料产生分解的可能性则会越大，故一般熔胶会采用中速为宜，如45%-75%，熔胶同时会碰到一个比较重要的环节，那就是背压的使用，产品精度要求越大，背压的使用则更大，背压可使原料分子间结构更紧密，成型出的产品则尺寸更稳定，外观越好。

The prior cycles with higher axial stress and larger strain range greatly restrains ratchetting strain of subsequent cycling with lower ones. Creep behavior plays an important role in the ratchetting strain and its influence on ratchetting behavior can not be neglected. Fracture morphology characteristics of two kinds of materials were investigated by scanning electron microscope. It shows that failure of material A is induced by cavitation and that of material B is induced by decohesion. For material A, with the decreasing strain amplitude the fracture surface shows more larger diameter globular particles under uniaxial loading and can be seen more obvious and deep crack under multiaxial loading. However for material B, with the decreasing strain amplitude fracture surface shows larger and larger scalelike shape and becomes more smooth under uniaxial loading, but fracture surface under multiaxial loading looks like more smooth than that of uniaxial loading, and shows gradually wave-like morphology.

通过扫描电子显微镜研究表明：材料A为空穴引起的失效，材料B为剥离导致疲劳破坏；随着载荷幅值的减小，材料A在单轴载荷下，断口表面浮出更多更大直径的球状颗粒，而多轴载荷下，可以看到很深的裂纹；随着载荷幅值的减小，材料B在单轴载荷下，断口表面鱼鳞片越来越大，表面越来越平整，而多轴载荷与单轴载荷相比，断口表面看上去更加平整，并且随着载荷幅值的减小，断口逐渐呈现波浪形貌；通过微观的傅立叶变换红外光谱分析，结果表明随着应变幅值的增加，无论载荷是单轴还是多轴状态下，橡胶材料吸光度比值随着幅值的增加而增加，这说明体系中的结晶含量也随之增加。

The main products of the company : double/single screw stem extruder, aluminium-plastic compound pipe,(PP-R, PE,PVC)copper plastic compound pipe,plastic special-shaped material, plate, sheet material, foamed plastic picture frame material, belt for packing, plastic pipe material, plastic graining and other sets of production line and series of high-speed heating/cooling mixing unit, drying machine, feeding machine, crusher, grinding machine, dehydrating drying machine, mould temperature controller, water cooling machine, screening machine and other auxiliary equipment.

张家港华铭机械有限公司是由张家港市塑料机械的开创者群体经优化重组而创建，主要从事塑料机械产品的研发制造，主要产品有单、双螺杆挤出机、铝塑复合管、(PP-R、PE、PVC)铜塑复合管、(PVC、PC、PE、PS等)塑料异型材、(PVC、PE、ABS、PP、PS)板材片材、塑料发泡镜框型材、打包带、塑料管材、塑料造粒等成套生产线，以及系列高速加热、冷却混合机组、干燥机、上料机、破碎机、磨粉机、除湿干燥机、模温控制器、冷水机、分筛机等各类辅机周边设备。

This invention discloses a preparation method for anti-corrosion rare earth magnet material characterizing that it takes the optimized grain-boundary phase design as the starting point on the basis of a dual alloy method to select Nd base alloy with high crystal forming ability as the assist alloy and reduces the temperature of the press mold blank in a quartz container to room temperature from over grain-boundary phase melting point with the water extraction way to get enough cooling rate and guarantee the non-grain-boundary phase, compared with the material of the same composition prepared by ordinary method, the weightlessness of this invented material reduces over 30% after testing the weightlessness of the material by laying it for 96 hours under 121deg.C, 2 atmosphere and 100% humid environment to show the advanced performance of anti-corrosion.

本发明公开了一种耐腐蚀稀土永磁材料的制备方法，其特征是它在双合金法制备工艺的基础上，以优化晶界相设计为出发点，选取具有较高非晶形成能力的Nd基合金为辅合金，并在烧结回火时将置于耐高温石英容器中的压型坯件，从晶界相熔点以上以水淬冷却的方式降温至室温，以达到足够的冷却速率，确保得到非晶晶界相，根据本发明制得的耐腐蚀稀土永磁材料，通过测量在121℃、2个大气压以及100％湿度环境下放置96小时后材料的失重情况，结果显示本发明得到的材料与常规方法制备的相同成分的稀土永磁材料相比失重减少了30％以上，充分证明其具备了更优越的耐腐蚀性能。可广泛应用于电子、汽车、计算机、电力、机械、能源、环保、国防、医疗器械等领域。

Don not attempt to do something which you can not to do.

不要企图做那些办不到的事情。

The expression of CTGF and TNF-αweredetected by immunochemistry and the number of Clara Cells was calculated.

光镜下观察肺组织的病理变化，采用免疫组化染色观察肺组织中结缔组织生长因子和肿瘤坏死因子-α的表达和Clara细胞的数量。