查询词典 solidification

The article introduces and regards cement as the main pharmaceutical of the solidification pharmaceutical, through the purpose-built deep layer mix machinery, mix solidification pharmaceutical and ground soil by force, make the soft soil harden into a treatment method of ground with globality, water and stability and body of a pile of certain intensity.

1深层搅拌法概述深层搅拌法是用于加固饱和软粘土地基的一种方法，它是利用水泥、石灰等材料作为固化剂的主剂，通过特制的深层搅拌机械，在地基深处就地将软土和固化剂强制搅拌，利用固化剂和软土之间所产生的一系列物理化学反应，使软土硬结成具有整体性、水稳定性和

This paper introduces the current methods to treat solid wastes abroad such as cement solidification, fly ash thermo-treatment, chemical solidification, chemical lixiviation and so on.

飞灰的处理是控制重金属污染的关键，目前处理垃圾焚烧飞灰中重金属污染物的常用方法有：水泥固化法、化学药剂稳定法、飞灰热处理、化学浸提法等，生物淋滤法是近年新兴起来的金属浸提技术。

Based on the recent research results of solidification, computer, electromagnetics, mechanics and Magnetohydrodynamics, the institute formed a subject-constructive way that crossed multi-disciplinary and characterized by EPM(Electromagnetic Processing of Materials) and computer optimization of solidification.

本研究所积极吸取金属凝固、计算机、电磁学、力学和磁流体力学等学科的近代研究成果，走出了一条多学科交叉的、以材料电磁加工和凝固过程计算机优化为特色的学科建设道路。

An active mold temperature control method was presented and applied in solidification by developing a measure and control system. The forming process was controlled by the active outer controllable temperature field, which was brought by the individual heating and cooling units distributed in the proportional spacing towards the solidification direction in the mold.

摘 要：提出一种主动式模具温控方法，并开发测控系统将其应用于凝固成形中，通过主动的外加可控温度场来控制零件成形过程，实现零件按自下而上的顺序凝固。

By combination of the finite differential technique with the upper bound elemental technique, simulation for the technology of extrusion directly following liquid infiltration which involves infiltration, solidification, and large plastic deformation in one process has been realized and the essences of various technical processes have been revealed by their corresponding simulation results showing the variation of the infiltrated depth and the temperature field with time during infiltration, the punch position, the solidification development of the matrix alloy, the state of the composite within the deforming zone, and the forming load required at different times during extrusion.

采用有限差分法和上限元法相结合，对融浸渗、凝固和大塑性变形为一体的液态浸渗后直接挤压工艺过程进行了数值模拟，从浸渗时浸渗深度与坯料温度场随时间的变化以及挤压过程不同时刻的冲头压下位置、坯料凝固情况、变形区坯料状态、成形载荷大小等方面揭示了不同工艺条件下的各种挤压过程的实质。

One, two and three recalescence events in the solidification of highly undercooled Ni_(68)B_(21)Si_(11) alloy melt and the conditions of undercooled together with the effect on solidification morphologies were revealed.

发现深过冷Ni_(68)B_(21)Si_(11)合金液形核过程中的多次再辉现象，揭示了二次和三次再辉的过冷条件，以及对凝固组织的影响。

Gscoh gs fsR, gscoh as the solid fraction when the formation of the continuous dendrite framework, fsR as the maximum solid fraction after recalescence,βs as the solidification shrinkage of the primary phase,μas the dynamic viscosity of the liquid, a as the length of L/S coexistence zone,λ2 as the secondary dendrite arm spacing, and tf as the total solidification time. High temperature recovery and recrystallization taking place in these fragments during further cooling results in the further grain size decrease.

本文通过对过冷DD3高温合金再辉过程中累积应力的计算，得到作用于初生枝晶的累积应力σs，可表示为：式中，gl是液相体积分数，gs是固相体积分数，gscoh是连续枝晶网络形成点对应的固相分数，fsR是再辉结束后固相分数，βs是快速凝固中液固收缩率，μ为液态合金的动力学粘度，a是再辉中液固共存区长度，λ2是枝晶二次间距，tf是总凝固时间，即再辉时间。

The mature of pseudo-recalescence is the remelting of dendrites. This leads to apparent refinement of dendrite microstructures. Therefore the experiment support the viewpoint of dendrite remelting for microstructure refinement during supercooling solidification.②Under the condition of supercooling solidification, secondary recalescence cannot show up for single phase solid solution.

伪再辉现象的本质是枝晶熔断所致，由此引起伪再辉试样微观组织被明显细化，从而支持了深过冷凝固过程中组织细化的枝晶熔断说观点；②单相固熔体合金，在深过冷凝固条件下，不可能出现二次再辉。

In order to investigate the influence of surface tension gradient driven convection on solidification behavior of alloys under microgravity, remelt and solidification of Al-Al〓Ni eutectic alloys, which have characteristics of directional growth along temperature gradient, were carried out on board Chinese retrievable satellite.

利用我国返回式科学实验卫星搭载的梯度炉和Al-Al〓Ni共晶合金定向生长的特点，研究了与重力无关的表面张力驱动对流（Marangoni对流）对合金凝固行为的影响，在空间微重力下获得了弯曲的双涡放射状共晶组织。

In other side, a lot of investigation results indicate that the rotating magnetic field and static magnetic field have significant effects on solidification process. These show a potential application of the RMF and SMF in industry. However, the detailed mechanisms of the RMF and SMF during melt solidification process are still unclear.

另一方面，对凝固行为和凝固机制的理解一直是科学工作者追求的目标，研究表明旋转磁场和静磁场具有影响合金凝固行为的重要作用，但是，对磁场在凝固过程中的作用机制的研究还处于探索阶段，很多问题尚待解决。

Molecular Distillation is a kind of high vacuum distillation method, which is suitable for the separation of high boiling, heat sensitivity and viscidity products.

分子蒸馏技术是一种在高真空条件下进行的连续蒸馏过程，适合于分离高沸点、热敏性及具有生物活性的混合物。

They are to the Noughties what yuppies were to the Eighties .

那在六十年代是时髦的，但在八十年代肯定是过时了