查询词典 slant

However,there have been no papers which have investigated Minkowski and Minkowski slant helices and Minkowski conical geodesic curves so far as.In this paper,our major study is to give the definition of Minkowski general helix and Minkowski slant helices and Minkowski conical geodesic curves in indicators 1 in pseudo-Euclidean three-space (that is, three-dimensional Minkowski space), and study the definition of equivalence Minkowski general helix, By considering geometric invariants of these space curves, we can estimate the order of contact with those special curves for general space curves.

本篇文章主要研究在指标数为1的3维伪欧氏空间(即三维Minkowski空间)中，我们给出Minkowski一般螺线、Minkowski斜螺线和Minkowski锥面测地线的定义，研究Minkowski一般螺线的等价定义，给出Minkowski斜螺线和Minkowski锥面测地线作为三维Minkowski空间中的特殊曲线所特有的性质，并通过考虑三维Minkowski空间曲线的几何不变量，估计Minkowski斜螺线和Minkowski锥面测地线这两种特殊曲线和一般Minkowski空间曲线切触的阶数。

NJWGY3665 bacterial strain is inoculated in a glucose nutrient culture medium to carry out the slant culture, the culture temperature is 28 to 37 DEG C and the culture time is 2 to 6 days;(2) seed culture: a spore which is cultured on a slant is produced into a single-spore suspension by using sterile water, which is also inoculated in a seed culture medium for culture, the temperature is 28 to 32 DEG C, the rotational speed is 200rpm and the culture lasts for 2 to 6 days;(3) fermentation culture: the seed liquid is inoculated in a fermentation culture medium for culture, the temperature is controlled at 28 to 37 DEG C, the pH is controlled at 6.0 to 9.0, the rotational speed is 180 to 220rpm, the fermentation lasts for 5 to 9 days, so as to obtain the Streptomyces sp., methanol or ethanol is used for the extraction and separation of mycelium through the method of centrifugal separation, then the resin method is adopted for carrying out refining, so as to obtain the peptide antibiotics enramycin.

NJWGY3665菌种接到葡萄糖营养培养基中，进行斜面培养，培养温度28-37℃，培养时间2-6天；(2)种子培养：用无菌水将斜面上培养的孢子制成单孢子悬液，并接种到种子培养基中培养，温度为28～32℃，转速为200rpm，培养2-6天；(3)发酵培养：将种子液接种到发酵培养基中培养，温度控制在28-37℃，pH控制在6.0-9.0，转速180-220rpm，发酵5-9天，得到链霉菌，采用离心分离的方法将菌丝体用甲醇或乙醇进行提取分离，再采用树脂方法进行精制，获得多肽类抗生素安来霉素。

The article with the intercept outside aerosphere implement to study a target, consider amount of miss the target is very small approach rate mediumly with intercept process bigger, be aimed at engine to be able to offer constant thrust only, can be started for many times and have pulse job state, and do not have change the character of thrust job status, apply slant buy scale guides brought a law to design agree with the switch threshold value that course controls engine.

本文以大气层外拦截器为探究对象，考虑到脱靶量很小和拦截过程中的接近速度比较大，针对发动机只能提供常推力，能多次启动并具有脉冲工作状态，且不具有变推力工作状态的特性，运用偏置比例导引律设计了适合于轨控发动机的开关阈值。

The load that uses fiber model law to analyse concrete of round CFRP- steel tube to control curved component part - in sectional deflection curve, analytic result and test result be identical are better and slant at safety.

采用纤维模型法分析圆CFRP-钢管混凝土压弯构件的荷载-中截面挠度曲线，分析结果和试验结果吻合较好且偏于平安。

Based on force diagram an analytical expression between some factors and splaying angle of the bar is brought forward, pointing out that splaying angle of the bar should be 2 3 degrees, and slitting angle should be 30 degrees approximately, outboard slant angle on the slitting groove should be 45 50 degrees and bite angle should be 7 8 degrees.

为稳定小规格带肋钢筋的三线切分轧制，对涉及棒材张开角的切分孔孔型诸角度进行了分析，通过对轧件受力状态的讨论，提出了诸因素与棒材张开角之间的解析式，指出满足三线切分稳定轧制时的棒材张开角应为 2°～ 3°，相应的孔型切分角为 30°左右，孔型外侧壁倾角应在 4 5°～ 5 0°之间，咬入角可控制在 7°～ 8°之间等。

The editorial had an antiunion slant.

这篇社论有一种反工会的倾向。

Slant-Neck These hosels often are plumber-necks that bend back from the shaft line.

Slant-Nect：这类型的杆颈将其往杆面之前倾斜，这样的方式会再加上可观的OFFSET值，也增加了更多向上击球的质量。

The accompanying text rarely misses a chance to put the Holy See's slant on history, but this is still a bibliophile's treasure house.

附加文本很少错过把罗马教廷的偏写搬上历史的机会，不过它仍是爱书人的宝库。

Adding a slight slant to the sides of the cover reduced the overall bulkiness and made it easier to insert the plugs.

添加轻微倾斜对包括双方减少了整体的笨重并使其更容易插入插头。

Use 16 pinhead thorn to defeat the subcutaneous tissue that is in into pin mark first before receiving an injection, in order to make puncture needle enters target area smoothly, need puncture stitch the needle arrives at cyst center to slant a bit next place, pull out needle core, receive on inject...

在进针前先用16号针头刺破进针点处的皮下组织，以使穿刺针轻松顺利地进入靶区，待穿刺针尖到达囊肿中心稍偏下部位，拔出针芯，接上注射。。。

It was just a normal day of school

那只是上学的普通一天

Which is a very good reference in this issue.

这是一个在这个问题上很好的参考。