查询词典 rear

Angulation front and rear must be balanced and adequate to give forward reach and rear drive.

前后肢的角度协调，有足够的角度，可以提供充分的前躯伸展性和后躯驱动力。

Angulation front and rear mustbe balanced and adequate to give forward reach and rear drive.

前后肢的角度协调，有足够的角度，可以提供充分的前躯伸展性和后躯驱动力。

Rear angulation is moderate, and balance of front and rear angulation is of paramount importance.

后躯角度适中，前后躯角度平衡是至关重要的。

An arrow-shaped turning indication plate is respectively arranged on the mud blocking tiles at the middle and the rear of the vehicle, a turning control knob is arranged on the left end of the bicycle handle bar, and the turning control knob is connected with the front and the rear turning indication plates by the flexible shaft.

一支箭-作形了旋转指示碟子分别地是安排在泥阻断上铺以瓦在中央和车辆的后面，旋转控制拉手利是安排骑乘脚踏车柄酒吧的左边结束，和那转控制拉手利与前面和后面旋转指示碟子一起连接被有柔性桥。

An arrow-shaped turning indication plate is respectively arranged on the middle of the bicycle handle bar and the fender-tile at the rear of the bicycle , a turning control knob is arranged on the left end of the bicycle handle bar, and the turning control knob is connected with the front and the rear turning indication plates by a flexible shaft.

一个箭头形转折迹象显示板是分别安排在中间的自行车处理酒吧和挡泥板瓦，在后方的自行车，一个转折控制旋钮被安排在左侧底自行车处理酒吧，并把控制旋钮连接在前方与后方转折迹象显示板挠性轴。

It has no handlebar, one front wheel, one front foot board capable of controlling direction, one rear foot board, one accumulator and one rear wheel between two foot boards, and one wheel hub motor and one brake in the center of the rear wheel.

为了进一步减小传统电动车的体积和重量，本折叠电动车采用无龙头设计，两端各有一个脚踏板，两脚踏板间为蓄电池和后轮，后轮中心为轮毂电机和刹车装置。

The monocoque carbon seat stays lightens up the rear of the frame and provides optimal power transfer to the rear wheel, but it has to be said that there's not much 'give' in this rear end.

一体成形的后上叉减轻车架的后半部分也提供了到后轮最理想的力量传输。但也要说这后三角部分没有任何的妥协让步。

It is attached to the rear bodyshell clam via rear end plates which not only increases the stiffness of the whole structure but also ensures that as much of the airflow as possible passes over the rear wing.

它是连接到后方车身蛤通过尾部的车牌，不仅提高了整个结构的刚度，又能保证尽可能多的，超过了尾翼可能通过气流。

The swing auto-tricycle comprises an auto body, which is divided into front and rear as a front body 1 and a rear body 2. The front body 1 is swingably connected to the rear body 2 through a swing joint mechanism.

具备将车体前后分割的前部车体(1)和后部车体(2)，前部车体(1)通过摇动式连接机构与后部车体(2)连接，并可以自由摇动。

New box design with durable 0.5 inch (13 mm) paving skin Vertically-adjusting mold mount for precise leveling of mold to machine Telescoping end sections with 12 inches (305 mm) of width variation on each side are available Standard paving depth is zero to 24 inches (610 mm)Edge slump adjustment Hydraulic Vertical Hinged Sideplates, self-contained inside the mold for track clearance Split, pressure-compensated sideplates Folding side plate wings for transporting without removing Pivoting mold mounting beam to eliminate stress points Self-supported TA is hydraulically driven with 3.5 inch (89 mm) ACME screws for up to a six inch (152 mm) crown Front and rear top T-bar on mold for attaching accessories and structural integrity Inserts are bolted together with front and rear alignment pins for easy mold assembly New vibrator mounting tube attaches to T-bar on mold – Vertical vibrator lift – Rear lubrication system with grease zerks accessible from the work bridge New strike-off – Mounted on paver frame T-rail, independent of the mold – New modular design with wedge lock system for ease in changing widths – 10 inches (254 mm) of hydraulic height adjustment – Hydraulic crown adjustment Spreader plow mounted to paver frame T-rail, optional auger available Tamper bar optional

与耐久性的新的箱子设计铺精密水准测量的0.5英寸(13 mm)皮肤垂直调整的模子登上模子用机器制造挤撞与12英寸(305 mm)的末端部分在每边的宽度变异是可利用的标准铺的深度是零对24英寸(610 mm)边缘暴跌调整水力垂直的取决于的Sideplates，独立性在轨道清除分裂的模子里面，折叠运输的pressure-compensated sideplates旁边板材翼没有去除在轴上旋转的模子架置射线消灭重音点Self-supported TA水力驾驶与3.5英寸(89 mm)由六英寸(152 mm)冠决定的尖端螺丝在前后冠上在模子的T酒吧附有的辅助部件并且结构正直插入物与容易的模子汇编新的振荡器架置管随员T酒吧的定位销一起在前后被闩上在模子–垂直的振荡器推力与油膏zerks的–后方润滑系统容易接近从新工作的桥梁触击–在摊铺机框架足迹，模子的独立登上了与楔子锁系统的–新的模块设计在改变的宽度的舒适的– 10英寸(254 mm)水力高低调整–水力冠调整分布器犁登上了对摊铺机框架足迹，任意任意木钻可利用的堵塞器的酒吧

But in the course of internationalization, they meet with misunderstanding and puzzlement.

许多企业已经意识到了这一点，但在国际化的进程中，仍存在一些误区与困惑。

Inorder toaccomplish this goal as quickly as possible, we'll beteamingup with anexperienced group of modelers, skinners, and animatorswhosenames willbe announced in the coming weeks.

为了尽快实现这个目标，我们在未来数周内将公布与一些有经验的模型、皮肤、动画制作小组合作。