查询词典 radius

Finally it analyzes the feasibility that using hydromechanics to analyze traffic flow by contrasting various characters between traffic flow and fluid flow. It analyzes influence of road alignment to basic expressway segment capacity by hydromechanics, and obtains viscous resistance and viscous movement differential equation when the vehicle drives on circular curve segment of expressway. And it infers that viscous resistance is correlated with sideway force coefficient, slope of crown and radius of circular curve. Radius of circular curve, sideway force coefficient and slope of crown are bigger, viscous resistance is smaller, the influence to capacity is smaller when the vehicle is running on nearside lane of circular curve; but radius of circular curve and sideway force coefficient are bigger, slope of crown is smaller, viscous resistance is smaller, the influence to capacity is smaller when the vehicle is running on fast lane of circular curve.

最后通过对比交通流与流体流的相似性，运用流体力学分析了道路线形对快速路基本路段通行能力的影响，求出了车辆在曲线路段的粘性阻力，建立了车辆在曲线路段的粘性运动微分方程，并由此推知，粘性阻力与横向力系数、路拱横坡度和圆曲线半径都有关系，当车辆在圆曲线外侧车道上行驶时，圆曲线半径、横向力系数和路拱横坡度越大，粘性阻力就越小，对道路的通行能力影响就越小；而当车辆在圆曲线内侧车道上行驶时，圆曲线半径和横向力系数越大，路拱横坡度越小，粘性阻力就越小，对道路的通行能力影响就越小。

The iris radius of 60 (93 eye) patients with early pupillary block primary angle closure glaucoma was measured with this method, it showed:(1) there was a statistically significant difference in iris radius between the patients with early stage primary pupillary block angle closure glaucoma and the normal subjucts (53 cases 106 eye) with the age matched group (P.01),(2) it is proved with the stepwise discriminatory analysis that the iris radius-the most significant bio-anatomic parameter of the anterior segment is usefull to diagnose early primary pupillary block angle closure glaucoma by stepwise discriminatory analysis.

本研究用此测量法测量了60例93只眼早期原发性瞳孔阻滞性闭角型青光眼的虹膜曲率半径，发现：（1）早期原发性瞳孔阻滞性闭角型青光眼患者的虹膜曲率半径小于同年龄正常人（53例106眼）的虹膜曲率半径，其差异具有显著性统计学意义（P.01）；（2）经多因素逐步判别分析证明本研究所提出的活体眼前节解剖学测量参数——虹膜曲率半径有助于原发性瞳孔阻滞性闭角型青光眼早期诊断。

Lanthanides belong to the sixth cycle of the periodic table Ⅲ B family, are all solid metal, they are La, Ce, Pr, Nd, Pm, Sm, Eu, Gd, Tb, Dy, holmium, erbium, thulium, ytterbium, and lutetium were 15 kinds of metals and their periphery are two layers of electronic 5d16s2, while the peripheral third layer f orbital but never zero to 14, so the external electronic structure of 4f0-145d16s2, and therefore these elements in oxidation number are to 3, very close chemical properties, extraction, when it is difficult to separate them they are mostly multi-element mineral mix, more difficult to increase refining, and their atomic number of 57-71, one by one to increase the number of protons the nucleus, and thus extranuclear electron of gravity is also growing, so that atomic radius decreases with increasing atomic number Z, which makes lanthanides contraction, ionic radius is also reduced, which also makes Zr, Hf, Nb and Ta, Mo and W, the atom and ionic radius very close to each other they also determine a similar nature, resulting in difficult separation, also the tribe Ⅷ of the fifth cycle, ruthenium, rhodium, palladium, and the sixth cycle, osmium, iridium, platinum is very similar in nature, thus The six elements, said platinum group elements.

镧系元素属于周期表第六周期中ⅢB族，全部是固体金属，它们是镧、铈、镨、钕、钷、钐、铕、钆、铽、镝、钬、铒、铥、镱和镥共十五种金属元素，它们的外围两层的电子均是5d16s2，而外围第三层的f轨道电子却从零增加到14个，所以外围电子结构为4f0－145d16s2，而使这些元素氧化数均为＋3，化学性质极为接近，提炼时很难分开，它们的矿石又大多是多种元素混在一起的，更增加提纯难度，它们的原子序数为57－71，核内质子数逐个增加，因而对核外电子引力也不断增强，使原子半径随原子序数Z增加而减小，这就使镧系元素收缩、离子半径也缩小，这也使得Zr和Hf，Nb和Ta、Mo和W等原子和离子半径都很接近、也决定了它们彼此性质类似，以致难以分离、也使第Ⅷ族中第五周期的钌、铑、钯和第六周期的锇、铱、铂在性质上极为相似，因而称这六个元素为铂系元素。

Because the workpiece is in dynamic balance, the resultant moment acting on it should be zero. Introducing the moment from lapping tool and press head a moving differential equation is built. In this equation only workpiece rotating speed is unknown. It means that workpiece rotating speed can be got by this equation. Since there is a transcendental function in integral function of the equation an analytic result can not be got, only digital result can be got by a computer. Thus a change rule of workpiece rotating speed with lapping parameters is known, e.g. the radius of press disc ball socket, radius of press head ball, the distance between the workpiece rotating axis and lapping tool rotating axis, workpiece radius, modulus of elasticity of the press head and press disc, friction coefficients between the lapping tool and workpiece, and between the head and disc, pressure between the lapping tool and workpiece and pressure between the press head and press disc.

因工件处于动态平衡状态，其上所受到的来自于磨具和压头的力矩应相等，将二力矩表达式联立，建立工件运动微分方程，该方程中只有工件的旋转角速度是未知量，因此可以求出工件旋转角速度，但该方程积分式中含有超越函数，得不出解析解，只能通过计算机求出数值解，得出工件旋转角速度随各研磨参数的变化规律，如压盖球座半径、压头的球头半径、工件回转中心相对磨具回转中心的偏心距、工件半径、压头和压盖材料的弹性模量、磨具与工件间的摩擦系数、压头压盖间的摩擦系数、磨具与工件间的压强、压头压盖间的压力等。

The type and the size of epidermis cell, epidermis hair, stomata apparatus and inside blade tissue;Ascertaining by measuring the epidermis cell thickness of the stem, the type and density of the epidermis hair,the density of lenticel; the thickness of cortex, phellogen, vascular tissue and pith;And calculate the ratio of cortex and radius, the ratio of vascular tissue and radius, the ratio of pith and radius…….

测定出叶片表皮细胞、角质层和厚角组织厚度，表皮毛、气孔器和叶内组织的类型、大小等；测定出茎的表皮细胞厚度，表皮毛的类型和密度，皮孔密度，皮层、栓皮层、维管组织和髓的厚度，计算皮层与半径之比，维管组织与半径之比，髓与半径之比等。

Hook empty-load, outward travel at low speed and extreme position limiting at max radius is 5m jib(outward R=50m,inward R=7.5m), enable one switch of the radius limiter(outward and inward travel is controlled by its parting limiter switch), when the trolleying to and extreme position limiting at max radius, enable another limiter switch(ourward and inward limiter switch), then trolley stop travel, when travel it again, the trolley just travel in the center of the jib frame.

4.4.3 幅度限位器调整(结构调整方法见外购件说明书) adjusting method for radiuslimiter(the procedures is shown as the outsourcing instructions)(1)吊钩空载，以低速档运行，向外行至距最大幅度处5 米时(向外时 R=50 米，向内时 R=7.5 米)，幅度限位器中的一个开关恰好动作(向外，向内分别由一个限位开关控制)，当小车行至最大幅度时，另外一个限位开关动作，小车停止运行，再启动时，小车只能往臂架中央运行。

This project studies the scale-dependent deformation behavior of the metal matrix composite, the void nucleation and void growth mechanisms at the micron/submicron scale. The main results are:(1) In prophase, growth and coalescence of the void embedded in the graded matrix are analyzed in detailed;(2) Based on the infinite solid model containing a micro-void, coupling effects of the void shape and the void size on the void growth are studied carefully, the results show that it seems to exist a critical equivalent void radius, which is associated with the material length. When radius of a microvoid is close to or smaller than the critical void radius, the micro-void growth rate is essentially eliminated;(3) The coupling effects of the particle shape and size on the mesoscopic stress fields within the particle and matrix are also investigated by introducing the conception of inclusion/matrix interfacial energy. The results show that the stress concentration factors within the particle and on the matrix/particle interface are also strongly size-dependent,so the void nucleation mechanism is size-dependent.(4) By employing a specific orthogonal curve coordinate frame and a 'kernel function' conception, a 'unified method'solving the spheriodal and spherical void problems is suggested; by this unified method, size-dependent plastic potentials of the porous materials containing the spheriodal or spherical voids are obtained, which extend the traditional Gurson model for the spherical void and GLD model for the spheriodal voids to the micron scale.(5) Based on the RVE model containing the spheriodal or spherical particles, the influences of the particle shape and size on the size-dependent mechanical behavior of metal matrix composite are studied.

中文摘要：本项目对金属基复合材料在微细观尺度下的尺度相关变形行为、孔洞形核及长大的机理和模型进行了研究，取得了如下主要结果：1）在前期研究中，探讨了基体的梯度分布对孔洞长大和聚合的影响；2）基于含孔洞的无限大体模型，探讨了孔洞形状和孔洞尺寸对其长大的耦合作用，结果表明：可能存在一个与材料特征长度相关的临界孔洞尺寸，当椭球孔洞的等效半径小于临界孔洞半径时，孔洞的长大受到明显抑制；3）通过引入基体/夹杂界面能的概念，分析了夹杂尺寸、夹杂形状对材料细观应力场的耦合影响，结果表明：颗粒内部和界面上的应力集中因子强烈地依赖于夹杂的尺寸和形状，因此，孔洞的形核机理是尺寸相关的；4）采用一种特殊的正交曲线坐标系和引入"核函数"的概念，"统一"地得到了含椭球和球形孔洞的材料的尺寸相关塑性势，它将传统的Gurson球形孔洞模型和GLD椭球孔洞模型推广到微尺度范围；5）基于含椭球和球形夹杂的体胞模型，初步研究了夹杂形状、夹杂尺寸对金属基复合材料尺寸相关力学行为的影响。

Therefore, it has the important scientific research value in studying the relationship between the changing of the parameters (including the temperature, the humidity, the grain radius and so on) and the electricity and radioactivity of the medium. Applied the count statistics and the numeral value analysis, the paper analyzes, concludes and contrasts the data sufficiently through the experimentation, and acquires the following results that the resistivity and the polarizability both have the negative relationship with the temperature variety of medium from 0℃ to 200 ℃. The parallactic poalarizability is consistent with the temperature variety in the plan as well as the section, but their trends are exactly opposite. Power supply voltage has no considerable influence to the resistivity and polarizability by using duality variance analysis, however, the detecting depth and the plan position influence them greatly. Different AB/2 interval that increases by degree does not influence variance and the average value of the resistivity and the polarizability remarkably. By using the least double multiplication, the relationship of temperature-time-the influence radius of the fire source is carried up by the mathematic drawing up. After discussing their correl ation, I educe the influence radius of the fire source and carry out the 'trend analysis and forecast to the spacial changing of the temperature and the parallactic polarizability in the end.

本文通过试验并应用数理统计和数值分析等相关理论对所得到的试验数据进行了分析、归纳和对比，得出了介质温度变化在0-200℃内视电阻率和视极化率与温度均表现为负相关性；视极化率与温度在剖面和平面上的变化形态具有很好的一致性，但变化趋势相反；由二元方差分析可得供电电压对视电阻率和视极化率无显著影响，但探测深度和平面位置对视电阻率和视极化率有显著影响；通过假设检验可证不同AB／2递增间隔，对视电阻率和视极化率的方差和平均数影响都无显著性差异；应用最小二乘法对温度——时间——火源影响半径之间的关系进行了数学拟合，讨论了它们之间的相互关系，得出了火源影响的有效半径，太原理工大学硕士研究生学位论文并对温度和视极化率的空间变化作了趋势分析和预测。

The squares of Bessel functions are plotted about O on the equator and on the first , second, third an fifth layer lines for half of the nucleotide mass at 20 A. diameter and remainder distributed along a radius, the mass at a given radius being proportional to the radius.

的平方贝塞尔函数绘制关于澳赤道和第一，第二，第三行的第五层的一半，在20个核苷酸大众答：直径和其余分布在半径，大众在某一半径正在比例到半径。

Based on the relations among the stress, final wall-thickness of thin-walled tube and the characteristics of tube material, original size, curling radius along with friction condition in a axially-compressed internal inversion process on right-angled fillet die, some analytical discriminants were established for judging if a double-layered tubular piece of aluminum alloy could be steadily formed from a certain-sized round tube via internal inversion process without interference and plastic instability of tube wall, and a method was put forward for determining the maximum and minimum usable curling radius or die fillet-radius for thin-walled tubes in the process.

基于薄壁管直角圆角模轴压内翻过程中各处应力及最终壁厚与管材特性、管坯尺寸、卷曲半径及摩擦条件之间的关系，推出了判别任一铝合金双层管件可否由特定尺寸圆管稳定内翻成形而不出现管壁干涉与塑性失稳问题的解析判别式，指出了确定薄壁管圆角模内翻卷曲半径或模具圆角半径极限值的方法。

More than five decades after the Indian constitution promises a casteless society, there is no sign that the castes are disappearing.

在印度宪法允诺一个&无种姓&社会五十多年后，种姓尚没有显示出任何要消失的迹象，但变化也确确实实地发生了。

Don't distract him from his studies.

他在学习不要打扰他。