查询词典 process input output

The merits of the inclusion of quantitative methods based on logical empiricism for explicit definition of input errors and uncertainty, approaches to quantisation of input data, and optimisation of outputs are contrasted with soft systems approaches that incorporate more linguistic and information theory into landscape analysis.

为输入的错误和不确定，输入的数据的量子化的方法和输出的最佳化的明白定义以合乎逻辑的经验主义为基础的数量方法的包含的功绩与将较多的语言学和传播理论纳入风景分析的软性系统方法一起对比。

The results show that the plasticity zone and dynamically quiescent layer become fine equiaxed recrystallisation under the thermo-mechanical effect, the grains in the heat-affected zone grow up because of the effect of friction heat. When the rotation speed is 2 500 r/min and the welding time is 12 s, good joint is achieved, and the tensile shear strength of the joint reaches 9.24 kN. The tensile shear strength of spot increases with increasing tool rotation speed, with increasing welding time, the strength increases first, while then reduces. The microhardness of plasticity zone is high, but is slightly lower than that of the base metal, the minimum value of microhardness is in the heat affected zone. When the energy input of joint is high, the fracture type of spot is mode Ⅰ, and the tensile shear strength is high; on the contrary, when the energy input of joint is less the fracture type of spot is mode Ⅱ, and the strength is low.

结果表明：塑性区和动态静止层的晶粒在热和力作用下发生动态再结晶形成细小的等轴晶，热影响区的晶粒在摩擦热作用下长大变粗；搅拌头旋转速度为2 500 r/min，焊接时间为12 s时，可以获得力学性能较好的焊点，焊点的剪切强度达到9.24 kN；焊点的剪切强度随搅拌头旋转速度的增大而增大，随焊接时间的延长先增大后减小；塑性区的显微硬度较高，但略小于母材，接头显微硬度的最小值分布在热影响区；焊点热输入量较多时，接头为Ⅰ型断裂，焊点的剪切强度较高；焊点热输入量较少时，接头为Ⅱ型断裂，焊点的强度较低。

According to password which establishes, uses two pressed keys realizations password the input function, after the password input is correct, locks opens, if inputs three passwords are not correct, locking presses a key 3 seconds, simultaneously discovered reports to the police the sound, after has not pressed a key presses down 3 kinds, only then opens the pressed key locking function; Otherwise still had the pressed key in 3 seconds to press down, relocked presses a key 3 seconds time and reports to the police

根据设定好的密码，采用二个按键实现密码的输入功能，当密码输入正确之后，锁就打开，如果输入的三次的密码不正确，就锁定按键3秒钟，同时发现报警声，直到没有按键按下3种后，才打开按键锁定功能；否则在3秒钟内仍有按键按下，就重新锁定按键3秒时间并报警

Ment must be in zero input or input shortcircuit or an adjustment signal.

注意：调节SPAN比率值和量程设定后，必须检查零点看是否需要重新调整，调零时必须在零输入或者输入一个所需调零值，如4~20mA输入

Notes:Afterthe adjustment of span value and scale setting,you need to check whether zero nment must be in zero input or input shortcircuit or an adjustment signal.Fox example,inputting4~20mA,if you want to display

注意：调节SPAN比率值和量程设定后，必须检查零点看是否需要重新调整，调零时必须在零输入或者输入一个所需调零值，如4~20mA输入

Ment must be in zero input input shortcircuit an adjustment signal.

注意：调节SPAN比率值和量程设定后，必须检查零点看是否需要重新调整，调零时必须在零输入或者输入一个所需调零值，如4~20mA输入

Notes:afterthe adjustment of span value scale setting,you need to check whether zero need to be resetteel.zeto adjust-ment must be in zero input input shortcircuit an adjustment signal.fox example,inputting4~20ma,if you want to display

注意：调节span比率值和量程设定后，必须检查零点看是否需要重新调整，调零时必须在零输入或者输入一个所需调零值，如4~20ma输入

Input Your program will input data for different sets of stockbrokers.

输入， 你的程序将输入的数据为不同的股票经纪人。

The properties are the dispersion equation of IREBs drifting in the tube, and the transmission line model of IREBs interacting with the gap electrical field of input cavity of RKA and bunching in the drift tube. The expression of modulated current after the gap of input cavity is got, which is content with the experimental results.

建立了IREBs在漂移管中传输的色散方程，以及IREBs与RKA输入腔间隙电场相互作用和IREBs在漂移管中群聚传输的传输线模型，获得了电子束经过输入腔间隙后产生的调制电流表达式。

The system is partly a multivariable control system which means that one output action variable (e.g. chemical charge) is controlled from more than one source (e.g. two feed forward signals, one feedback signal and an operator bias input).

该系统是部分的多变量控制系统，就是说一个输出动作变量是由多于一个的源变量(比如两个前馈信号，一个反馈信号和操作员的偏置输入)来控制的。

Tom: You are right, he worked hard all the time.

你是对的。他一直都是努力工作。

Take shortcomings,failures,and mockings of others as commonplace and a drive to complete oneself,hold your own opinion over the evalution and disscution divested from others,afterwards sink into the state of eliminate mistakes if any or encourge oneself being not being influenced by the sayinngs of others or having no ideas to do.

把缺点、失败及别人的耻笑等看成是一种常事，当成完善自己的动力，对别人的评价和议论自己心中有主见，做到&有则改之，无则加勉&，不为人言所左右或无所适从。