查询词典 principal axis

Electronic barke applied to both principal axis and stroke,flexible axis enables the adjustment of synchoronus brake

主轴、冲程均用电子刹车，调整时主轴可自由旋转，可方便地调整到同步刹车。

If not, the bearings will be worn and the life will be shortened, The methods of maintenance are as follows: oiling once for each shift. It should be noticed that the oil channel must be cleaned immediately if the oil is not be consumed or the loss is slow then 50# motor oil should be added. The oil cup is placed on the upper end of principal axis. Each shift should add 3# lithium base grease once with grease gun on bearing of principal axis base and bearing of milling roller. Disconnect and clean the analyzer once for 6 months and apply 3# lithium base grease. Apply lithium base grease for bearing room.(see lubrication system for details).

保养方法如下：主轴加油时间每班一次，但必须注意，发现油杯的油没有损耗或损耗太慢时，应立即清洗油道，再加50#机械油，油杯位置在主轴上端，主轴底座轴承，磨辊轴轴承每一班用黄油枪加注3#锂基润滑脂一次，分析器轴承每六个月拆开清洗一次，加足3#锂基润滑油，风机轴承室加锂基润滑脂。

The experiment shows that the adoption of Moiré fringes of the circular grating can make highprecision torque measurement of the principal axis meet the requirement, which offers a new noncontact method for the measurement of mechanic principal axes.

实验结果表明，采用圆光栅莫尔条纹可以达到主轴扭矩高精度测量的要求，为机械主轴测量提供了一种新的非接触式测量方法。

When the tongs installs on the machine bed principal axis, the tongs install the to should have the enough match accuracy with principal axis cowgirl surface, and guarantee the gearing the stability dependable.

当夹具体在机床主轴上安装时，夹具安装基面与主轴相应表面应有足够的配合精度，并保证安装稳定可靠。

The tongs all passes in the machine the gearing on the bed what tongs the gearing on realizes with superficial contact in the cowgirl on the bed in machine or matches.when the tongs installs in the machine bed work on the stage,the center of gravity of the tongs should be as far as possible low,center of gravity the more high an accepts should the dint is more big,the tongs bottom four directions should bulge,make its contact good,or the bottom establishes four a feets.when the tongs installs on the machine bed principal axis,the tongs install the to should have the enough match accuracy with principal axis cowgirl surface,and guarantee the gearing the stability dependable.

夹具体在机床上的安装都是通过夹具体上的安装基面与机床上的相应表面的接触或配合实现的。当物流设备需要的公司体在机床工作台上安装时，夹具的服装厂应尽量低，重心越高则支承面应力越大，夹具底面四边应凸出，使其接触良好，或底部设置四个支脚。当夹具体在机床主轴上安装时，夹具安装基面与主轴相应表面应有足够的配合精度，并保证安装稳定可靠。

Motion synchronization between tool in X direction and principal axis rotation was controlled by electronic gearbox in cam turning. And profiling mechanism could be superseded by servo tool-holder. Linear motor direct drive servo tool-holder was designed, and host-slave control system with PC and DSP was developed for the require of high-speed and realtime servo. The technical process was analyzed in cam turning. Servo tool holder with tool swinging and principal axis variable rotate speed were presented to keep constant cutting angle and speed.

将电子齿轮箱用于凸轮车削加工系统的传动，以伺服刀架取代了传统加工的靠模装置，实现了刀具X方向直线运动与机床主轴转动的同步控制；设计了直线电机直接驱动的伺服刀架及基于PC与DSP构成的上—下位机控制结构，采用DSP进行实时控制以满足高速伺服需要；对凸轮加工过程的工艺特点与恒角度、恒速度车削进行研究，提出了具有刀具摆动功能的伺服刀架与机床主轴变转速运动方案。

This can result in a splitting ofwavelength-dependent loss band and make the codirectional mode coupling condition (of the fundamental core mode into cladding modes) be different at two principal input polarizations.In a PM-LPG fabricated with a PMF having relatively small birefringence , the adjacent resonant dips (slow-axis and fast-axis resonant dips) resulting from the two principal input polarizations have identical cladding mode order and the wavelength separation between them is several nanometers

这可能导致分裂的ofwavelength-dependent损失，使codirectional乐队的耦合条件(模式基本核心人才培养模式为层模式)是不同的两种主要的输入波在PM-LPG捏造和具体情况有相对较小的双折射，相邻的谐振(slow-axis和fast-axis引起共振蘸)的两种主要模式有相同的输入波的波长层顺序和他们之间的分离是几奈米的图案

Based on the processed accessory, the number, the position and the machining data of the holes and the form of the principal axis are determined; The driving way of the headstocks are drawn, the power is transmits by the methods of optimization, the driving parameter are determined, the structure of the principal axis are designed and the strength of the parts, such as the gears and the bears, are checked.

根据被加工零件确定加工孔的数量、位置、切削用量及主轴类型，拟订了主轴箱的传动方式，应用最优化方法传递功率，削减振动，确定传动参数，设计轴的结构，进行如齿轮、轴承等相关零件的强度校核计算。

The calculation of principal axis box includes the school of the school pit, principal axis of the school pit, key of the school pit, bearings of the school pit, stalk of school pit, wheel gear of rubbing the clutch to calculate calculate etc.

主轴箱的计算包括摩擦离合器的校核、齿轮的校核、轴的校核、轴承的校核、键的校核、主轴的校核计算等。

The calculation of principal axis box includes the school of the school pit principal axis of the school pit key of the school pit bearings of the school pit stalk of school pit wheel gear of rubbing the clutch to calculate calculate etc.

主轴箱的计算包括摩擦离合器的校核、齿轮的校核、轴的校核、轴承的校核、键的校核、主轴的校核计硕羧。

Graf, without question, is the greatest women's player in history.

格拉芙，现在，毫无疑问是女子网坛历史上最伟大的选手。

If not, you will have to look around at all your important data.

如果没有，您将需要检查所有的重要数据。