查询词典 plasticizing

Gelatinized corn starch was prepared by a co-rotating twin-screw extruder,and through drying and comminuting process. Thermoplastic starch was prepared with the gelatinized corn starch powder as raw material and glycerol and Polyvinyl Alcohol as plasticizing agents. Thermoplastic starch sheet was prepared with extruding process. Degree of gelatinization was tested by a polarizing microscope. Mechanical properties of prepared thermal plastic starch sheets were studied in relating to type and amount of the plasticizing agents.

利用双螺杆挤出机对玉米淀粉进行糊化处理，经干燥、粉碎后制得预糊化淀粉，以其为原料，添加甘油，PVA为增塑剂制备热塑性淀粉，经模压制备片材后，通过偏光显微镜分析了淀粉的糊化情况，研究了甘油含量和PVA含量变化对材料性能的影响。

The composite system of combination by extrusion with injecting,the is one kind of new system of injection and plasticizing , the raised function and property which injection and plasticizing .

挤出和注射相结合的挤注复合系统，是一种新型的塑化注射系统，提高了塑化注射的功能和性能。

The main reasons for currently domestic PVC plasticizing difficulty were analyzed, and the mechanism to improve plasticizing characteristic were also introduced.

分析了目前国产聚氯乙烯树脂塑化性能差的主要原因，介绍了其塑化性能改善的机理，论述了聚氯乙烯树脂塑化性能改善进展现状及发展方向。

The influence of the glycerol contents on the plasticizing and mechanical properties were studied.

研究了甘油含量对材料的增塑作用及其对力学性能的影响。

Scanning electron microscopy showed that the original tapioca starch granule was destroyed, mixed plasticizer penetrated into the granule interior, successfully plasticizing the tapioca starch, and made it into a uniformly continuous phase.

扫描电镜表明，混合塑化剂尿素和乙醇胺已经渗透到木薯淀粉颗粒内部，塑化了木薯淀粉，使其颗粒被破坏，成为均一连续相。

The regenerated cellulose film prepared by cuprammonia method is firstly undergone plasticizing and drying then coated on two sides with the mixture of degradable low mole-cular weight polyurethane and unsaturated polyester, the water proof film is obtained after solidifying and crosslinking.

按铜氨法制备再生纤维素膜经增塑、干燥后用可降解性的低分子量聚氨酯和不饱和聚酯混合涂料在膜两面涂布，固化交联得到防水膜。

All results point to that 7%wt plasticizing agent add into PA1010 can receive high ensile strength and impact strength.

将这种热致液晶聚酰胺与尼龙1010共混，并加入N-乙基-对-甲苯磺酰胺作为增塑剂，进行了结构与性能的研究。

The process is carried out by rubbing into filament raw materials, digesting in plasticizing liquid of sodium hydrate and sodium silicate at 100-130degree for 1-2hrs to obtain plasticized raw material, high-speed agitating plasticized raw materials with non-metallic minerals, octadecanoic acid and silicon oil at 100-130degree for 15-45hrs, coating and drying to obtain the final product.

先用农用搓揉机直接搓揉成丝状物料，然后丝状物质在含氢氧化钠和硅酸钠的塑化液中于100～130℃下蒸煮1～2小时，得到塑化物料，最后将塑化物料同改性非金属矿粉、硬脂酸和硅油在100～130℃下高速搅拌15～45分钟进行包覆处理，干燥后便得到目标产物。

It was iound in the experiment that the glass fiber made crystal peak temperature raise 8~9 ℃, Crystal original taper to be large, spherocrystal size small, it -acted the function of hetero-geneous nucleation for polypropylene . High density polyethylene has plasticizing efficancy and combined effect of hetero-geoeous nu...

试验表明PP/GF/HDPE复合物的结晶峰温度升高8～9℃，结晶起始斜率变大，球晶几何尺寸明显减小，复合物中的玻璃纤维起到异相成核作用，高密度聚乙烯对聚丙烯有增塑作用并对异相成核具有协同效应。

The results showed that the resistant property to high temperature will be increased as the content of hollow glass-bead increased, flame-retardant effect was evident as the content of fire retardant A was above 20%, tetrachloromethane was the best one as single solvent, and the amount of plasticizing agent was usually at the range of 5%~8

结果表明，随着中空玻璃微珠含量的增加，涂层材料的耐温性能有所提高；阻燃剂A的含量在20%以上时，阻燃效果非常明显；四氯化碳是单一溶剂的最佳选择；增塑剂用量一般控制在5%~8%。

Molecular Distillation is a kind of high vacuum distillation method, which is suitable for the separation of high boiling, heat sensitivity and viscidity products.

分子蒸馏技术是一种在高真空条件下进行的连续蒸馏过程，适合于分离高沸点、热敏性及具有生物活性的混合物。

They are to the Noughties what yuppies were to the Eighties .

那在六十年代是时髦的，但在八十年代肯定是过时了